New Items Forum
Register

Total Price

$0.00

Cart 0 Cart 0 Loading...

HKS-9257 High Speed Servo 4.5kg / 0.07sec / 25g

HKS-9257 High Speed Servo 4.5kg / 0.07sec / 25g

Shipped From:
  • USA
  • Global
QTY:

Now save save $0.00 $0.00

$11.24
Status:
In Stock
SKU:
HKS9257
WANT FREE SHIPPING? Click here to find out more!
HKS-9257 is a high speed, high torque digital servo, Suitable for HK500/Align Trex-500 size Helis.

Specs:
Dead band: 0.002ms (Default)
Control System: +Pulse Width Control
Working frequence: 1520μs / 80hz Digital mode/Analogy mode
(RX) Required Pulse: 3.0~5.0 Volt Peak to Peak Square Wave
Operating Voltage: 4.8~6.0 Volts DC
Operating Temperature Range: -10 to + 60 Degree C
Operating Speed (4.8V): 0.08 sec/60° degrees at no load
Operating Speed (6.0V): 0.07 sec/60° degrees at no load
Stall Torque (4.8V): 3.8 kg.cm
Stall Torque (6.0V): 4.2 kg.cm
360° Modifiable: NO
Motor Type: Brushed Motor
Potentiometer Drive: Indirect Drive
Driver Type: FET
Bearing Type: Dual Ball Bearings
Gear Type: Plastic gear
Programmable: YES
Connector Wire Length: 18.0
Dimensions: 36x15.3x21.8 mm
Weight: 25 g
Spline count: 25

 


Equipped with two ball bearings.
For use with the Futaba GY401 (FUTM0807, FUTM0808) and the GY502 gyros.
Does not work with these Futaba radios (4FG, 5FG/K, 6FG, 6FG/K, 7FG/K New Terratop, 3EGX, 3PGE, 2NL, 2LGX, 2FR, 2PK series) These radios have a servo neutral signal of 1310us not compatible with this servo.
Do not use with AM radios.
 
 
 
 
  • SKU HKS9257
  • Brand HobbyKing
  • Shipping Weight 43.0000
  • Length 130.00
  • Width 15.00
  • Height 90.00
  • Torque(kg)(min. 0.01kg) 4.50
  • Speed (Sec/60deg) 0.07
  • A(mm) 33.00
  • B(mm) 36.00
  • C(mm) 30.00
  • D(mm) 15.00
  • E(mm) 49.00
  • F(mm) 20.00
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

I buy two piece to in EDGE 540 alerion. These servos are ok, but one sometime no find her center

playlist_add_check Overall:
trending_up Value:
verified_user Quality:

I buy two piece to in EDGE 540 alerion. These servos are ok, but one sometime no find her center

Seems to be a good servo. Got 1 that was bad from the start, didn't move correctly and finally stopped working before I even got to fly. bought two extras for replacements just incase.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Seems to be a good servo. Got 1 that was bad from the start, didn't move correctly and finally stopped working before I even got to fly. bought two extras for replacements just incase.

nice servo for tail 500 size

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

nice servo for tail 500 size

Leider nicht besonders solide. Fr ein 1,60 m 3D Modell definitiv nicht geeignet, obwohl die Servogre es htte vermutenlassen.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Leider nicht besonders solide. Fr ein 1,60 m 3D Modell definitiv nicht geeignet, obwohl die Servogre es htte vermutenlassen.

great servo centers fine en lighting fast crispy controles.

works fine on a 450 size heli! but keep youre gyro on standard frame rate! so for those who usen a 401 type gyro etc

higher frame rates will cause damage!

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

great servo centers fine en lighting fast crispy controles.

works fine on a 450 size heli! but keep youre gyro on standard frame rate! so for those who usen a 401 type gyro etc

higher frame rates will cause damage!

Ich habe den Servo in den T-Rex Kolne asl Heckservo eingebaut. Von oben in den Halter hat aber nicht geklappt, weil dieser etwas hoch in der 24g klasse ist. Von unten hat aber wunderbar geklappt.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Ich habe den Servo in den T-Rex Kolne asl Heckservo eingebaut. Von oben in den Halter hat aber nicht geklappt, weil dieser etwas hoch in der 24g klasse ist. Von unten hat aber wunderbar geklappt.

Purchased and installed on a hk500cmt tail. I only used it for approx 5 minutes before the servo stripped out. I was running 5.5v to the servo and this servo said it can handle 6v. I wouldn't recommend this servo.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Purchased and installed on a hk500cmt tail. I only used it for approx 5 minutes before the servo stripped out. I was running 5.5v to the servo and this servo said it can handle 6v. I wouldn't recommend this servo.

Fast and reliable servo, great combination on blade 400 with 401B AVCS. Must mount on additional tail boom holder for servo.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Fast and reliable servo, great combination on blade 400 with 401B AVCS. Must mount on additional tail boom holder for servo.

I bought this servo for HK450 PRO v2 as a tail servo. It`s not a straight fir. I need to adjust the corners on the mounting plate of the heli to fit.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I bought this servo for HK450 PRO v2 as a tail servo. It`s not a straight fir. I need to adjust the corners on the mounting plate of the heli to fit.

gzel bir rn verilen reti hakediyor

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

gzel bir rn verilen reti hakediyor

Customer files
tech specs Download [43]
Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!

Combine Essential Items and Save