New Items Forum
Register

Total Price

$0.00

Cart 0 Cart 0 Loading...

Hobbyking i86 Multi-Rotor Control Board

Hobbyking i86 Multi-Rotor Control Board

Now save save $0.00 $0.00

$21.43
Status:
Out of stock!
SKU:
070000006
WANT FREE SHIPPING? Click here to find out more!

Controlled by an Atmel Mega168PA 8-Bit RISC based micro controller and utilizing a single 3-axis MEMS gyro the Hobbyking i86 Multi-Rotor Control Board is capable of 8 Multi-rotor craft types and 2 flight modes without the need to flash the micro controller. The simple dip switch systems allows for quick and easy selection of your desired Multi-rotor configuration and flight mode.

Light weight and compact the i86 can fit in the smallest of craft and includes a small piece of double sided tape to install.

The Hobbyking i86 Multi-Rotor Control Board supports:
Aero (fixed wing)
Dual copter
Tri copter
Quad copter X
Quad copter +
Hex copter
H6 copter
Y6 copter
All of the above modes can be set in "Normal" mode or "Sports" mode (default normal)

Specs:
Input Voltage: 4v to 6v
Input signal: 50hz standard PPM
PWM Frequency: 400hz for ESC, 50hz for servos
Gyro scale: +/- 500dps, ODR: 800hz
Operating temp: -40° C to 85° C
Size: 40mm x 40mm
Weight: 8g

  • SKU 070000006
  • Brand HobbyKing
  • Capacity (mAh) -
  • Shipping Weight 25.0000
  • Length 123.00
  • Width 10.00
  • Height 80.00
  • 900 Tricopter at Burfoot Park
  • Xcopter Scratch built with a HK i86 controller
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

great board
great price too took only a few minutes to set up
highly recommend this
board really good for filming with pots around 75pcnt
not so great for acro unless update firmware which is easily done with a usb asp i brought 2 !

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

great board
great price too took only a few minutes to set up
highly recommend this
board really good for filming with pots around 75pcnt
not so great for acro unless update firmware which is easily done with a usb asp i brought 2 !

Works well ! Quick and easy setup, good price!

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Works well ! Quick and easy setup, good price!

Couldn't get it to work properly, even though, i did everything manual said. It starts shaking before you take off the ground. Maybe I didn't have enough experience with gain adjustment, but this was how I crashed my first quad...
I used it in st360 with multistar 20A ESCs and corona receiver.
Everything apart from shaking seems to be ok

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Couldn't get it to work properly, even though, i did everything manual said. It starts shaking before you take off the ground. Maybe I didn't have enough experience with gain adjustment, but this was how I crashed my first quad...
I used it in st360 with multistar 20A ESCs and corona receiver.
Everything apart from shaking seems to be ok

Can't quite believe I missed this important bug when disarming. I nearly got a 11" prop at full speed in the eye and it has ruined my 3 DT750 motors.
Please do not be complacent like I was, this board has not been fixed since all the bad reports regarding the disarm bug. DO NOT USE IT FOR MULTIROTORs. I don't care that it only seems to do it for SimonK ESCs, this is just not acceptable safe programming of a flight controller. I will be asking for my money back and money for the 3 DT750s. Sorry HK, you simply are playing with fire by selling these boards.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Can't quite believe I missed this important bug when disarming. I nearly got a 11" prop at full speed in the eye and it has ruined my 3 DT750 motors.
Please do not be complacent like I was, this board has not been fixed since all the bad reports regarding the disarm bug. DO NOT USE IT FOR MULTIROTORs. I don't care that it only seems to do it for SimonK ESCs, this is just not acceptable safe programming of a flight controller. I will be asking for my money back and money for the 3 DT750s. Sorry HK, you simply are playing with fire by selling these boards.

Couldn't make my Y-6 fly stable with it - was almost uncontrollable with whatever tune-ups I've tried. Replaced with KK2.1 and on the 1st flight copter hovered in the middle of the room with my hands down. There are much better boards now than this one.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Couldn't make my Y-6 fly stable with it - was almost uncontrollable with whatever tune-ups I've tried. Replaced with KK2.1 and on the 1st flight copter hovered in the middle of the room with my hands down. There are much better boards now than this one.

awesome controller , very flexible , easy to setup with dip switches , very stable
a good place to start in quadcopters

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

awesome controller , very flexible , easy to setup with dip switches , very stable
a good place to start in quadcopters

really chesp a great alternative to the kk board

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

really chesp a great alternative to the kk board

a great budget board once set up. mine was a bit tricky as it turned out the motor diagram was wrong. motor 2 should be motor 1, 3 = 2, 4 = 3, 1 = 4, once that was sorted it all worked fine, only rudder needed reversing on the tranny, so for the maiden, stable in the hover, just a slight drift to the right. I can correct that with a bit of sub trim. so a great budget board to start flying multi rotor machines

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

a great budget board once set up. mine was a bit tricky as it turned out the motor diagram was wrong. motor 2 should be motor 1, 3 = 2, 4 = 3, 1 = 4, once that was sorted it all worked fine, only rudder needed reversing on the tranny, so for the maiden, stable in the hover, just a slight drift to the right. I can correct that with a bit of sub trim. so a great budget board to start flying multi rotor machines

I got two of these for a project quad. Works pretty well and easy to use. It just takes a little patience with the pitch, yaw, and roll pots. Once you have them set, quad flies very well.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I got two of these for a project quad. Works pretty well and easy to use. It just takes a little patience with the pitch, yaw, and roll pots. Once you have them set, quad flies very well.

Little bit complicated to get working properly, but nice to fly when done properly. No self leveling feature, but good for training maneuvers and orientation. Nice and very cheap controller.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Little bit complicated to get working properly, but nice to fly when done properly. No self leveling feature, but good for training maneuvers and orientation. Nice and very cheap controller.

  1. 1
  2. 2
  3. 3
  4. 4
  5. 5
  6. ...
  7. 8
Customer files
HK i86 User Manual Download [933]
Tips montajes Download [3731]
So simple 1 Download [170]
No File Name Download [790]
rus review Download [0]
Manual_Rus Download [1176]
HK i86 manual Download [933]
i86 Stick Centering corrected Download [7811]
No File Name Download [396]
No File Name Download [933]
  1. 1
  2. 2
Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!

Combine Essential Items and Save