Hobbyking KK2.1.5 Multi-rotor LCD Flight Control Board With 6050MPU And Atmel 644PA
Hobbyking KK2.1.5 Multi-rotor LCD Flight Control Board With 6050MPU And Atmel 644PA
Copy and Share the Below URL
Accessories
The next evolution of the rotor revolution is here!! The KK2.1.5 is packing new found power with updated sensors, memory and header pins.
The KK2.1.5 is next big evolution of the first generation KK flight control boards. The KK2.1.5 was engineered from the ground up to bring multi-rotor flight to everyone, not just the experts. The LCD screen and built in software makes install and setup easier than ever. A host of multi-rotor craft types are pre-installed, simply select your craft type, check motor layout/propeller direction, calibrate your ESCs and radio and you’re ready to go! All of which is done with easy to follow on screen prompts!
The original KK gyro system has been updated to an incredibly sensitive 6050 MPU system making this the most stable KK board ever and allowing for the addition of an auto-level function. At the heart of the KK2.1.5 is an Atmel Mega644PA 8-bit AVR RISC-based microcontroller with 64k of memory. An additional polarity protected header has been added for voltage detection, so no need for on-board soldering. A handy piezo buzzer is also included for audio warning when activating and deactivating the board.
The KK2.1.5 added polarity protection to the voltage sense header and a fuse protected buzzer outputs, in case something is accidentally plugged in incorrectly. The voltage sense line has been updated for better accuracy. The board is clearly labeled and the voltage sense line color has been changed to red for easy identification, making installation and connections a snap.
If you’re new to multi-rotor flight or have been unsure about how to setup a KK board then the KK2.1.5 was built for you. The 6 Pin USBasp AVR programming interface ensures future software updates will be quick and easy.
Specs:
Size: 50.5mm x 50.5mm x 12mm
Weight: 21 gram (Inc Piezo buzzer)
IC: Atmega644 PA
Gyro/Acc: 6050MPU InvenSense Inc.
Auto-level: Yes
Input Voltage: 4.8-6.0V
AVR interface: standard 6 pin.
Signal from Receiver: 1520us (5 channels)
Signal to ESC: 1520us
Firmware Version: 1.6:
Pre-installed firmware.
Dualcopter
Tricopter
Y6
Quadcopter +
Quadcopter X
Hexcopter +
Hexcopter X
Octocopter +
Octocopter X
X8 +
X8 X
H8
H6
V8
V6
Singlecopter 2M 2S
Singlecopter 1M 4S
(Custom Mix via the "Mixer Editor" option)
The Mixer Editor allows you to adjust where and how much signal the motors receive from stick input and sensors. This allows you to create any configuration possible with up to 8 motors or servos.
What is a Multi-Rotor Control board you ask?
The HobbyKing KK2.1.5 Multi-Rotor controller is a flight control board for multi-rotor aircraft (Tricopters, Quadcopters, Hexcopters etc). Its purpose is to stabilize the aircraft during flight. To do this it takes the signal from the 6050MPU gyro/acc (roll, pitch and yaw) then passes the signal to the Atmega644PA IC. The Atmega644PA IC unit then processes these signals according the users selected firmware and passes control signals to the installed Electronic Speed Controllers (ESCs). These signals instruct the ESCs to make fine adjustments to the motors rotational speed which in turn stabilizes your multi-rotor craft.
The HobbyKing KK2.1.5 Multi-Rotor control board also uses signals from your radio systems receiver (Rx) and passes these signals to the Atmega644PA IC via the aileron, elevator, throttle and rudder inputs. Once this information has been processed the IC will send varying signals to the ESCs which in turn adjust the rotational speed of each motor to induce controlled flight (up, down, backwards, forwards, left, right, yaw).
** Note: It is all ways recommended to update to the latest software version as part of your initial setup.(this is different than v1.6 for 2.0)
-
KK2.1.5
-
RC UFO Flying Saucer
-
RC UFO Flying Saucer
-
RC UFO Flying Saucer
-
RC UFO Flying Saucer
-
RC UFO Flying Saucer
-
RC UFO Flying Saucer
-
RC UFO Flying Saucer
-
RC UFO Flying Saucer
-
Howd to set a board like this up?
-
HK FPV250 V2 Quad with kk2.1.5 flips rolls
-
KK2 SingleCopter 2m 2s Maiden
-
KK2 SingleCopter 2m 2s Maiden
-
KK2 SingleCopter 2m 2s Maiden
-
KK2 SingleCopter 2m 2s Maiden
-
KK 2.1.2 in Costa Rica
-
Start at 2:55
-
KK2.1.5 SK450 DeadCat
-
2018 UFO Flying Saucer Sighting with Tractor Beam
-
2018 UFO Flying Saucer Sighting with Tractor Beam
Jack | Verified Buyer
-
Overall
-
Quality
-
Value
good quality
Sep 23, 2017
screechhawk | Verified Buyer
-
Overall
-
Quality
-
Value
inexpensive
Aug 25, 2017
Jack | Verified Buyer
-
Overall
-
Quality
-
Value
needed to replace
Aug 03, 2017
George | Verified Buyer
-
Overall
-
Quality
-
Value
Great but weak screen
Feb 26, 2017
joseph | Verified Buyer
-
Overall
-
Quality
-
Value
Cannot reflash board
Oct 31, 2016
59gibson | Verified Buyer
-
Overall
-
Quality
-
Value
Customer Rated
Oct 06, 2016
FlyCH | Verified Buyer
-
Overall
-
Quality
-
Value
Customer Rated
Oct 06, 2016
lampo.ep | Verified Buyer
-
Overall
-
Quality
-
Value
Certified Buyer Rated
Aug 31, 2016
donatien | Verified Buyer
-
Overall
-
Quality
-
Value
Customer Rated
Aug 29, 2016
rudedog | Verified Buyer
-
Overall
-
Quality
-
Value
Certified Buyer Rated
Aug 08, 2016
KK2.1.X Instruktion Manual V1.16S1 Pro.p | Download [1517] |
No File Name | Download [1517] |
No File Name | Download [39] |
Manuale KK2 ITA =AsA= | Download [103] |
instruction manuale from steveis | Download [440] |
instructian manuale from steveis | Download [440] |
kk2.1 manual | Download [422] |
KK2.1 Manual | Download [422] |
KK2.1 march 2014 | Download [452] |
My KK2.1(7) updated firmware now using a | Download [1421] |
Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!