Are you sick of aerial photography camera ships looking like a UFO’s and flying slow and smooth like you’re taking grandma for a walk around the block? HobbyKing comes to the rescue with the new Super-H 600.
The new Super-H 600 is a 600mm class sport flying H configuration quadcopter. The optimal layout allows for all your gear to be safely mounted between the frame plates and on the centerline for maximum maneuverability. The upper frame has provisions for 12 vibration isolation balls allowing for jello free FPV and HD video recording. The isolation benefit of a clean and dirty plate also lets you have tighter flight controller PID values for a nice tight wobble free multirotor. The proven and readily available arms make replacement in the event of a “daredevil move gone wrong” easy and cheap. The frame layout can handle a huge range of batteries and equipment and has provisions for camera and forward mounting gimbals.
If you’re ready for a fun and yet utilitarian quadcopter the Super-H 600 exceeds all expectations.
• Prop free view with H layout
• Built from quality glass fiber and polyamide nylon.
• Pre-threaded brass sleeves for all of the frame bolts.
• Colored arms for orientation to keep you flying in the right direction.
• Anodized aluminum hardware
• Hook and rod Mounting options
• Large mounting tabs on the main frame bottom plate for easy camera mounting.
• Easy assembly
• Provisions for a clean and dirty vibration isolation frame
Motor to motor diagonal: 600mm
Motor mounting: 16~19mm
Frame plate length: 500mm
*Note: This frame has provisions for up to 12 vibration dampening ball for a clean and dirty system, the frame comes with aluminum standoffs standard. The vibration balls are sold separately and should be chosen depending on the given weight of the upper frame loaded.
I used this frame for a short time, because the holes are done badly. With well balanced 15" props there are too much vibrations even for a gimbal!!! It's not stable at all. When you will use it, use it with small motors and 12" props max. The max flight time I got with it was 30min, but it wasn't a nice flying via fav, because of the vibrations I hardly could see anything!!!What a waste. You get what you pay for. I ended up with genuine CW props and knock-off CCW props, and the slight difference in thrust at the same motor RPM caused the frame and super flexible arms to twist and yaw the quad in circles. Though correctly matching props are clearly called for, the HUGE amount offlex in the arms and lower / dirty frame of this quad made it a complete waste of my time to build. My AUW was around 2.5kg - I tried to build this around a 6s 4000mah system and a mid-size gimbal and camera. I suspect this would only work with a GoPro and a lightweight setup.Awful kit. Don't buy it. Very flimsy, not well machined. The frame is not symmetrical when assembled.simple fantastic. i have not used this for long but it is my first Quad copter frame and i think that it has been a good one to chose. I have been using it on grass and it has suffered lots of accidents but all in all it was great and there is NO damage to the board. i would recomend you use the NTM Prop Drive 28-30S 800KV / 300W Brushless Motor (short shaft version) motors and the Afro ESC 30Amp Multi-rotor Motor Speed Controller (SimonK Firmware) ESC's with Slow Fly Electric Prop 12x4.5R SF (4 pc - Green Right Hand Rotation) propellers as well as left hand turning ones and a 4 cell battery for me this set up has worked great. thanks for reading this, cyaYou pretty much get what you pay for. I've ordered this frame before and it was beside one drill hole fine. The second was missing all the drill holes for the rubber balls. Not a big deal for me. And the rest of the frame is descent and if you crash it (like I did), the replacement is not that big of a deal. I recommend this frame.This is nice big frame with a lot of space on it and it is cheap.
However it has few drawbacks:
- it is heavy, 500g
- arms could be longer, they can fit maximum 13" props
- little too elastic for my taste
- plates are made of tick plexiglass (12.5mm) instead of carbon fiber
- there are no hols for rubber dumpers, and once you drill it your self those holes violate structural integrity of plates
- holes made for gears on plates are made in a way that makes you difficult to attach some of your gears so you have to improvise
All 4 arms are black but I like it that way, it looks cool, and if you want better orientation you can put some colorized LEDs.
I have put some pictures in file section of my build. I'm using Multistar Elite 4007.740 motors, 12" 5.5peach propellers, 4.5Ah 3s battery, Crius v2 FCB and 20A Afro Slim ESC. total weight is 1750g, but I plan to add one more 4500mAh battery and d13" 5.5peach props. That should give me 15 minutes of flight time with good maneuverability.
This is a great frame. I have 14 inch blades on this build. If you do Use 14 inch props you will be cutting in close but still it makes for a nice long flight time! I suggest the use of m3x11MM vibration isolation grommits! They fit well! Enjoy!2210 turnigyA lot of gear for little money!
Nice easy build, some spares in mine (I hope they're spares!) And plenty of room. SJ400, APM GPS, 4x ESCS, FrSky Rx, FPV cam, Vtx and batt. And enough room to fit it all on again.As of January 2015 do NOT order this kit. The first time I ordered it, all that came in the box was a set of 4 black arms. Not sure if they were even for this kit or not. Filed an RMA, jumped through the hoops, got the 'replacement' shipped out and what greeted me when I opened the box? Another set of 4 black arms and nothing else. Clearly they are having an issue with the system, so this is a friendly heads up to everyone!
No File Name download now [3519kb] folding version download now [476kb] folding version download now [476kb] folding version download now [476kb] perfectly tuned and tested build i have download now [391kb] front view of gimbal mount with out cont download now [3130kb] top view of just mounted gimbal download now [2969kb] side view of my gimbal mounting system download now [3438kb] Quad Just built and flown download now [558kb] No File Name download now [3035kb] H600_01.jpg download now [403kb] H600_02.jpg download now [460kb] H600_03.jpg download now [392kb] H600_04.jpg download now [454kb] H600_05.jpg download now [436kb] New Build-Untested download now [0kb]