New Items Forum
Register

Total Price

$0.00

Cart 0 Cart 0 Loading...

Micro A-10 EPS Pusher Jet (PNF)

Micro A-10 EPS Pusher Jet (PNF)

Shipped From:
  • Global
Discontinued Product

Please continue searching for a similar product.
SKU:
A10PUSH
WANT FREE SHIPPING? Click here to find out more!

This Micro A-10 uses a brushless pusher motor that gives fantastic performance.
When test flown by the Hobbyking team, this little Warthog caused quite a stir. It flies so well you would have thought it was 3 times the size!

The 2.5g servo's are pre-installed and centred, the brushless ESC and motor are also pre-installed, assembly is fast and the model even comes with scale looking under-carriage for those flying off pavement runways. A full colour instruction sheet and decal sheet are included, as is a prop and prop saver.

Spec's:
Wingspan: 556mm
Length: 512mm
Flying Weight: 155g
Material: EPS
Motor: C10 Brushless Outrunner
ESC: 5A BEC
Servo: 2.5g x 2
3 Channel, thottle, aileron, elevator

Requires:
Your own 4 channel TX/RX
400~500mAh 2s Lipoly Battery

  • SKU A10PUSH
  • Brand -
  • Capacity (mAh) -
  • Shipping Weight 590.0000
  • Packaging Length 590.00
  • Packaging Width 95.00
  • Packaging Height 145.00
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

I got this free. Didn't really want it so I just grabbed the servos, motor and esc off of it.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I got this free. Didn't really want it so I just grabbed the servos, motor and esc off of it.

Looks is arguable but I got it as a freebie. Prop version flies better and longer than EDF. Also lot of cheaper in total (price plus shipping). It's an EPS materjal so not super crash resistant but it's light. That keeps the damage minimal. You can add some carbon in wing or fuselage for strenght.



Comes fuselage glued and all electronics and pushrods inside. Tiny ESC is at the back under the two canisters. No airflow inside the fuse but I don't know if heat will be an issue.

It has total 2 micro servos, one needs gluing/taping. No glue supplied but surely it needs some for assembly. Wing mounting plastic parts needs to be re-glued and one even few mm lower. So the wing doesn't fit snugly in stock situation. But anyway you have to re-glue some parts because they are glued weak in factory.



Canopy is held on with... nothing. U have to figure out some locking option - buy magnets or just rubber around the canopy. Under the canopy only battery fits so receiver goes in the middle where is very tight fit because of aileron servo. But some thin micro RX should even fit in da nose.

Two sheets of decals you can stick. Landing gear seems good and light. Elevator even has a carbon strip attached. No carbon in the main wing though.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Looks is arguable but I got it as a freebie. Prop version flies better and longer than EDF. Also lot of cheaper in total (price plus shipping). It's an EPS materjal so not super crash resistant but it's light. That keeps the damage minimal. You can add some carbon in wing or fuselage for strenght.



Comes fuselage glued and all electronics and pushrods inside. Tiny ESC is at the back under the two canisters. No airflow inside the fuse but I don't know if heat will be an issue.

It has total 2 micro servos, one needs gluing/taping. No glue supplied but surely it needs some for assembly. Wing mounting plastic parts needs to be re-glued and one even few mm lower. So the wing doesn't fit snugly in stock situation. But anyway you have to re-glue some parts because they are glued weak in factory.



Canopy is held on with... nothing. U have to figure out some locking option - buy magnets or just rubber around the canopy. Under the canopy only battery fits so receiver goes in the middle where is very tight fit because of aileron servo. But some thin micro RX should even fit in da nose.

Two sheets of decals you can stick. Landing gear seems good and light. Elevator even has a carbon strip attached. No carbon in the main wing though.

I got one again as a freebie. One wing side little bent and cracked tip but glue and time fix it. Motor mounted little off - have to re-glue. Wing doesn't fit in very easy - looks like have to re arrange the mounting parts. Also re-gluing some parts is a must.

Elevator servo inside is double side-taped and totally loose. Reglue or retape.

Marking on prop says 4x2.5R. Two planes both came with NO propsaver (sealed bags). No option to put the prop on and have to purchase mount separately now. Motor shaft is 2mm. Prop inside hole is 4mm.

I think I found that fits, search HK for C10-Saver.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I got one again as a freebie. One wing side little bent and cracked tip but glue and time fix it. Motor mounted little off - have to re-glue. Wing doesn't fit in very easy - looks like have to re arrange the mounting parts. Also re-gluing some parts is a must.

Elevator servo inside is double side-taped and totally loose. Reglue or retape.

Marking on prop says 4x2.5R. Two planes both came with NO propsaver (sealed bags). No option to put the prop on and have to purchase mount separately now. Motor shaft is 2mm. Prop inside hole is 4mm.

I think I found that fits, search HK for C10-Saver.

1 review sai:

I got the beast as a freebie. Fitting together good but u have to re-glue the plastic bits more stronger.

Battery connection is JST. Battery room is (mm): 95 lenght, 20 wide, 38-23 deep. I purchased (imo the best lipos for this plane) 2s 460mAh nanos. They are quite wide but fit nice but not right up in the nose. Removing some foam from underside of the canopy make the battery fit in the nose OK if needed. And the 500mAh zippy is same thing. I prefer 460mAh nano-tech over zippy. Same flight time, more power, longer life and lighter plane. Search HK for N460.2S.25

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

1 review sai:

I got the beast as a freebie. Fitting together good but u have to re-glue the plastic bits more stronger.

Battery connection is JST. Battery room is (mm): 95 lenght, 20 wide, 38-23 deep. I purchased (imo the best lipos for this plane) 2s 460mAh nanos. They are quite wide but fit nice but not right up in the nose. Removing some foam from underside of the canopy make the battery fit in the nose OK if needed. And the 500mAh zippy is same thing. I prefer 460mAh nano-tech over zippy. Same flight time, more power, longer life and lighter plane. Search HK for N460.2S.25

Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!

Combine Essential Items and Save