Featuring a Titanium Gear train and water/dust proof sealed case the MKS DS1210 can be dropped in water, caked in mud or buried in sand and still come back for more! Perfect for trucks and buggies. MKS servos are well respected in Taiwan, Korea and Japan.
Dead band: 0.002ms (Default)
Control System: +Pulse Width Control
Working frequence: 120Hz
(RX) Required Pulse: 3.0~5.0 Volt Peak to Peak Square Wave
Operating Voltage: 4.8~6.0 V DC Volts
Operating Temperature Range: -10 to + 60 Degree C
Operating Speed (4.8V): 0.15 sec/60° degrees at no load
Operating Speed (6V): 0.12 sec/60° dagrees at no load
Stall Torque (4.8V): 8.05 kg-cm (292.4 oz/in)
Stall Torque (6V): 10 kg-cm (365.3 oz/in)360°
Motor Type: DC Motor
Potentiometer Drive: Direct Drive
Driver Type: FET
Bearing Type: Dual Ball Bearings
Gear Type: Metal Gear
Connector Wire Length: 15.0 cm (5.9 in)
Dimensions: 40X20X40.30 mm (1.5748X0.7874X1.58 in)
Weight: 56 g (1.97 oz)
Very very good servo on T-Rex 600 or HK600 for cyclic. good torque, good speed, centering very well, and legendary MKS quality for a mini price!Bought one just to try when it first arrived. Put it in a Traxxas Slash 4x4, and it was a very noticeable upgrade compared to the stock servo. Have run it in pretty harsh conditions, and it seems to take the punishment well. Five stars all round. I just wish it would come in stock again so I could buy more of them.At first I installed this servo in my Inferno 1/8 buggy steering and it worked great, now I am using it in a Associated B4.1, almost way too much torque and speed. Very recommended.This servo works great! I am using it as my steering servo for my Losi LST 2. Since the splines on this servo is the same as a futaba I had not problems with the stock servo saver. The only comment have is that the stall torque is listed incorrectly on this site. I am pretty sure @6v it is 138.87oz/in and NOT 365.3oz/in. You should check yourself to make sure.Servo muy rapido, montado en mugen mbx6 dos meses sin problemas. Envio en 3 semanas por air mail normal (envio barato)Installed one in my Inferno 7.5 buggy and it is really good! Fast, strong and cheap. I recommend for any 1/8 buggy.I'm using these servos on my HK600GT... All i can say is wow. I am impressed they are super fast, super strong and very percise. I will use these on any Heli that I build that can take this size servo.Other servos that have faster specs aren't always fast when there is a load on it. these are so strong the load has no effect on the speed. SUPER SERVO.
I enjoy flying my HK600 better then my real trex helis cause of these.Put 3 of these in a T600 Esp. Need to mod a little bit because they are to long. Nothing hard to do. This servo looks very good, it's strong, quick and not too noisy. They will be perfect for my T600 FBLGood vervo on HK600GT cyclic. good torque, good speed, centering well. One of theim makes noise sometimes but no issue so far.I use this servos from month in my nitro heli - Elyq vision 50 Ultimate on swashplate and they work great. Servos are fast and strong. Execution is in the highest level. Extra advantage is waterproof. Watch this video http://www.youtube.com/watch?v=Wo0ucXOzWJI&feature=player_embedded
I chose those servos because this is best choice for someone who wants best product for lower price. I recomend it for nitro and electric 600 and 700 size heli.
David from Poland