The Turnigy Multistar Elite Outrunners are designed with one thing in mind - maximizing Multi-rotor performance! The new Multistar Elite motors are the new standard in Multirotor performance. Each Elite motor is built for a specific type/application allowing for further refinement and efficacy/power to be optimized.
Multistar Elite motors are more than a fancy name and new dark green color.. Built using the highest quality components from EZO Japan bearings, n45sh Magnets, .2mm laminations, 180deg oxygen free copper wire, .005g balancing, Perfect wind laid down and 100% QC, and then the design of each motor are also evaluated for their type application and everything from their mounting, to the prop type adapters are taken into consideration. The Elite motors are truly works of art
The Elite 5010 274KV Has been optimized for 6~8s operation and a 18~19inch propeller. The Motor comes with removable/replaceable knurled prop shaft and direct bolt style propeller mounting options. The 5010 provides ample torque for fast response providing a more stable platform in fast flight and windy conditions.
Multistar Elite is unmatched in quality and value, and the performance speaks for its self.
• EZO Japan Bearings
• N45SH Magnets
• .2mm Laminations
• 180deg oxygen free Copper wire
• .005g Or better balancing
• Perfect laydown windings
• 100% QC
• Replaceable prop adapter and direct bolt prop supported
Lipo cells: 6~8S
Max current: 630W
Max Amps: 28A
No Load Current: 0.43A/10V
Number of Poles: 12/14
Motor Shaft: 4mm
prop shaft: N/A
bolt hole spacing: 25*25mm
Lamination thickness: 0.2 mm
Bearing: EZO Japan
Balancing spec: 0.005g
See under "Files" tab for motor test data.
Unit Weight (g)
Max Currents (A):
Length B (mm):
Can Length D(mm)
Total Length E(mm):
Love this motor. I run them on 8S, 20A Afro HV controllers and a 18x 5.5 Quanum DJI style CF prop
1000g thrust at 9.8g/w 2000g around at 7.7g/w and a whoping 4600g peak thrust (!) at 4.7g/w with newly charged batteries, two 4S 8000mAh zippys in series. Amazing that the Afro 20A ESC seems to be able to withstand the 31A peak current draw. First time I found HobbyKing products to be underrated :-)
Setup: 8s Lipo, turningy 18x6.1 wooden multirotor prop, 40A HV mulistar ESC.
7.5g/w @2000g thrust
6g/w @ 3400g (max throttle on 8s, 29.6V)
Motor weight, 211g is with looong wires, the motor itself is around 190g
Nothing gets hot at full throttle, only warm.Awesome motor, lots of thrust runs so smoothOK. I have finally tested these motors on a Tarot x6 hex. Im using Flycolor 45amp escs. 20,000mah 10c Multistar 6s batt. Pixhawk Flight controller. THESE MOTORS are FLAWLESS!!!!!! Props are Tarot 18.55 carbon. Motor prop combo is perfect. Hovers at Mid stick with no change of mid throt adj. I get 27min hover in pos hold. Motors/escs com down cool. As i said,these motors are rebranded ARRIS 288kv. they are $89.00 as Arris sells them,and HK sells them for $50ish-All i can say is OUTSTANDING price and even BETTER motor.DO NOT HESITATE!!!Ok-This motor is not an 8s motorspecs say 22v max. it is a rebranded Aries 5010 288kv motor 6s max-SAME MOTOR!!!!! On 6s this motor works awesome on 6s with 1855 propson tarot x6So far,the build quality is outstanding!!! I have used several Multistar motors on many hex-quads which have exceeded my expectations-SERIOUSLY!!!! They have all held up with proper maint./!!!! A drop of oil will do wonders. You want your furnace motor to lastoil the bearingsHINT-HINT!!I have purchased 6 of these as well as 6 flycolor 45a 8s escs. This is for my Tarot x6 with Pixhawk. I will keep informed on setup and performace when done. Frank.