Country
United States
 
Shipped From:

MultiWii NanoWii ATmega32U4 Micro Flight Controller USB/GYRO/ACC

MultiWii NanoWii ATmega32U4 Micr...

QTY:

Now save save $0.00 $0.00

$20.31
Rating:
Stock:
OUT OF STOCK
Weight:
24g
SKU:
9387000009

Suggestion Box

Please let us know if you found any issues with this product listing.
We take our customer comments very seriously and in many cases our website modifications and product updates are a result of your comments!

Price War

If you've seen a product elsewhere for a better price, please let us know! HobbyKing pride themselves on offering the best price, so if there if you see something cheaper elsewhere, let us know!

Combine

essential items and
acc
Overview

The NanoWii is a complete multi-rotor flight controller. It is based on the ATmega32U4, which is the processor of the Arduino Leonardo and incorporates a MPU-6050 chip, which is a combined gyro and accelerometer.

This is the ultimate solution for powerful flight performance with your multi-rotor project, especially micro size models. The possibilities are endless with the NanoWii, only limited by your imagination!

Features:
• Ultra-compact size
• Based on Atmega32u4
• 6 RX inputs
• 6 HW PWM @ 11bit (better resolution, smoother response)
• Up to 8 motors or servos
• Invensense MPU6050 6 axis gyro and accelerometer (supports auto-level)
• Onboard USB
• UART connector (for bluetooth telemetry, GPS, DSM2 satelite etc)
• I2C connector (add barometer or magnetometer for heading hold and altitude hold)
 
Comes preloaded with Arduino bootloader (Leonardo)

Specs:
Main chip: ATmega32U4
CPU speed: 16MHz
Flash size: 32kB (3.3kB are taken by the Bootloader)
Input: 6 x high-res RX inputs (2 AUX channels)
Output: 6~8 motor outputs (motor 1-6 are 11-bit PWM)
Dimension: 30x30x16mm
Weight: 5.1g

*Note: This is not an original Arduino brand product.

Specs

Additional Information

  • Blade Count:
    N/A
  • Diameter X(Inch):
    No
  • SKU
    9387000009
  • Brand
    N/A
  • Watt Hour:
    0.00
  • Weight(g):
    24.00
  • Length
    110.00
  • Width
    20.00
  • Height:
    70.00
Discussion
Reviews

Write Your Own Review

Only registered users can write reviews. Please, log in or register

Quality
Value
Overall
Let me start off with a quick pre-summary: This board is an absolutely horrible piece of hardware.
I bought this thinking that I could get the reliability of a kk2.1 in a smaller form factor. Boy was I wrong.

The first quad I built is driven by a kk2.1 board. It took minimal time to set up, and flashing with Steveis allowed that little FC to control my quad as if it were on rails.

As for the nano multiwii board here, I can't even come close to saying the same thing. It drifts all over the place, PID tuning is near impossible, as none of the changes actually make any difference, it has a terrible response to stick position, especially with throttle. It suffers from, what I found on forums around the web to be called the "yo-yo" effect. Throttle will violently increase, and any attempt to compensate causes it to fall out of the sky.
But hey, At least it powers on, right?

I could continue, for quite some time, but I'm probably about to run out of text space.
So, Final summary... If you're looking for something reliable, go with the kk2.1 instead. It's not worth the waste of money to prototype the this mw board.
Quality
Value
Overall
Quality
Value
Overall
A real Pain to setup and connect and bad documentation. Once you get it to connect then maybe its ok but after getting a new PC and after spending 3hr trying to connect I ripped it out of my tricopter and just about tossed it in the garbage.
I so miss my original KK2.0:(
Quality
Value
Overall
Quality
Value
Overall
Good board. Simple, cheap and with good sensor. Ability to use on 2s without external BEC is nice as well.
As for flight and handling 0 it's just multiwii. Depends on setup and modifications, but I dare say that it's the best software for small and aerobatic copters around.
I've uploaded the picture of ISP connections. Programming via USB can be tricky sometimes because of your computer's drivers. But ISP programming always works flawlessly.
Recommended.

P.S. Having it supplied with pins unsoldered would be perfect.
Quality
Value
Overall
Quality
Value
Overall
I have this flight control on a 360mm quadcopter and it works very well. I am using the Bradwii firmware which has autotune. The only issue I had was missing the serial usb config line which then messed up the usb connection but I was able to reprogram using another arduino uno. Once I had the config.h set correctly the usb connection worked great with bradwii. This not the fault of the nanowii, it was my lack of experience. This flight controller works well and is very lightweight.
Quality
Value
Overall
Quality
Value
Overall
Nice board, really well suited to the 250FPV. You will have to do some research online to get it running but well worth it.
Quality
Value
Overall
Quality
Value
Overall
Sorry to say but this board or the Ardunio software it uses needs some work.
I have not been able to get Ardunio to upload new code through the USB port after may hours of trying. Tried different cables, ports, revision of software, manual reset of board and no go. It always hangs during the upload process
There is lot of NET discussion about problems with the Arduino Leonardo processor and this boards seems to suffer as well.
Really too bad as the price is good and it should do exactly what I want but if one can not download code, a Arduino Leonardo based board is no use at all.
Will steer clear of Arduino Leonardo based boards from now on.
Quality
Value
Overall
Quality
Value
Overall
Easy to setup and control
Quality
Value
Overall
Quality
Value
Overall
Great small Controller. Have 2 of them in use. If you want to use a Bluetooth module, you have to remove (break off) the white connector and unsolder the remaining pins. To mount them I used Gyro / Flight Controller Mounting Pads, also available at HK.
Quality
Value
Overall
Quality
Value
Overall
For $20, its an amazing board! No where near a CC3D, but then again, a CC3D is about 3X pricier. My only gripe about this board is the lack of mounting holes, so no way to hard mount this board to anything.
Quality
Value
Overall
Quality
Value
Overall
This is a great Fc board pretty easy to set up requires some small PID adjustments but once to get it tuned this board is extremely stable and it will also do flips very well. the only board i would rather have is the naze32 . if it had a barometer it might be better because it likes to change altitude randomly but its completely manageable. i have seen this board out perform APM, Hoverfly and other multiwii boards.
Quality
Value
Overall
View all reviews
Video
Upload video
File

Combine

essential items and
acc

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.