United States
Shipped From:
  • United States (US)
  • Global

NTM Prop Drive 28-26 1000KV / 235W

NTM Prop Drive 28-26 1000KV / 235W

NTM Prop Drive motors are rock-solid performance outrunners with tight windings, quality bearings, correctly rated magnets, balanced stator and flux rings plus they are QC checked at 14 points, from material processing all the way ...

Now save save $0.00 $0.00


Max Qty add to cart is -1 in one time

Suggestion Box

Please let us know if you found any issues with this product listing.
We take our customer comments very seriously and in many cases our website modifications and product updates are a result of your comments!

Price War

If you've seen a product elsewhere for a better price, please let us know! HobbyKing pride themselves on offering the best price, so if there if you see something cheaper elsewhere, let us know!


essential items and

NTM Prop Drive motors are rock-solid performance outrunners with tight windings, quality bearings, correctly rated magnets, balanced stator and flux rings plus they are QC checked at 14 points, from material processing all the way through to final dyno test.
Because we design and build these motors completely in-house (from 3D/2D drawing to materials sourcing, machining, balancing, final assembly and dyno) we can completely control production and ensure product consistency from design right through to shipping the product to you. The removal of middle-men has meant we can drive better value to the market and retail these motors at factory (our) prices! All performance figures are real and tested on our own motor dynos.

Our QC engineers check and balance each motor before shipping to the warehouse.

Model: NTM Prop Drive Series 2826 1000kv
Kv: 1000rpm/v
Poles: 3
Motor Wind: 19T
Max current: 15A
Max Power: 176W @ 11.1V (3S) / 235W @ 15V (4S)
Shaft: 3mm
Weight: 54g
ESC: 20~30A
Cell count: 3s~4s Lipoly
Bolt holes: 16mm & 19mm
Bolt thread: M3
Connection: 3.5mm Bullet-connector

Prop Test Data:
9x4.7 - 11.1V / 113W / 10.2A / 0.632kg thrust
9x6   - 14.8V / 220W / 14.9A / 0.937kg thrust

Note: An accessory pack is available for this motor. Please see the related items below.


Additional Information

  • Blade Count:
  • Speed (Sec/60deg):
  • Torque(kg)(min. 0.01kg)
  • Diameter X(Inch)
  • A(mm):
  • B(mm):
  • C(mm)
  • D(mm)
  • E(mm):
  • F(mm):
  • SKU
  • Weight(g)
  • Length:
  • Width:
  • Height
  • Kv(rpm/v)
  • Max Currents (A):
  • Power (W):
  • Length B (mm)
  • Can Length D(mm)
  • Max Voltage(V):
  • Shaft A(mm):
  • Unit Weight (g)
  • Diameter C(mm)
  • Total Length E(mm):
  • Resistance (mh):

Write Your Own Review

Only registered users can write reviews. Please, log in or register

Good little outrunner, I have noticed that there does appear to be slight bearing movement but doesn't affect operation. Nice quiet little unit
Really little motor, smaller than the images seem to be.

Make attention to the fact the rotor is 'inversed' I will post some video about it.

it seems to be a really nice power/weight ratio.
These motors are rock steady for the price. I have them on a 650mm quad and they do a great job. Running them with 20a esc's and have had no problems. Don't forget to get the prop adapters.
the real problem of this motor is the BEARINGS.
my advice is not to buy.
I bought this because i'm a beginner
good motor just dont expect to break any speed records very good for a trainer plane such as the bixlers
Installed these on my Q450 (upgraded from 2210n) and they made a huge difference. Same KV rating, but loads more power!
Nicely balanced and reasonably quiet, I flew around for 30 mins or so, getting through 2 LiPo's while fighting the breeze and the motors (and batteries) stayed nice and cool.

Definitely worth the money.
nice littel slow flyer motor. dynamically balanced but came with defective rear ball bearing. runs almost vibrationless after ball bearing was replaced. grub screw at the rear end was secured using some red colored screwlock. needed to wipe off the excess that did not cure.
bad bearing...bought 6 of them..2 craps because of bad bearing..dont really recommend this motor unless you want to change the bearing.
moteur de qualit pour le prix
I have recently bought 5 of these motors for a quad copter. 4 for the quad and 1 extra based on reviews. One of these motors was bad from the factory and would barely turn when put on the quad. Thankfully HK made it good and gave me credit. The first time I flew the quad on about the third flight 3 of the 4 motors broke, each loosing the circlip and the shaft either coming part or all the way out of the motor. Please don't waste your money on these motors for you quad they are horrible and will not hold up.
View all reviews
  • HK X900 Tricopter with NTM Prop Drive 28-26 1000KV motors

Upload video

Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!


essential items and

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.