New Items Forum
Register

Total Price

$0.00

Cart 0 Cart 0 Loading...

Openpilot Mini CC3D Flight Control Board

Openpilot Mini CC3D Flight Control Board

Shipped From:
  • Global
QTY:

Now save save $0.00 $0.00

$15.91
Status:
In Stock
SKU:
571000053-0
WANT FREE SHIPPING? Click here to find out more!

Openpilot Mini CC3D Flight Control Board

This is the new Mini CC3D flight controller. It is about half the size of the regular CC3D but has the same functionality. The Mini CC3D board is an all-in-one stabilization hardware flight controller, which runs the OpenPilot firmware. It can fly any airframe from fixed wing to an octocopter and is configured and monitored using the powerful and user friendly OpenPilot Ground Control Station (GCS) software.

Using the powerful STM32 32-bit micro-controller gives you crisp handling characteristics when flying your flying tricopter, quad, hex, octocopter, and even fixed wing planes. The tiny size allows you to fit this on even the smallest frames.

Don’t be fooled by the size. Mini CC3D provides comparable functionality to other high-end flight controllers at a small fraction of the cost.

Features:
• About half the size of the regular OpenPilot CC3D, but with the same functionality.
• The CC3D provides a crisp feel when flying tricopters, quads, hexas, octocopters, and even fixed wing planes.
• Powerful STM32 32-bit micro-controller running at 90MIPs with 128KB Flash and 20KB RAM.
• 3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer.
• 4 layer PCB for superior electrical noise reduction and flight performance.
• Software support for Windows, Mac and Linux.
• Direct high speed USB support with no drivers required.
• Spektrum satellite receiver support.
• Futaba S-BUS hardware support.
• Innovative Flexi-port technology for superior port flexibility.
• 4Mbits on-board EEPROM for configuration storage.
• This OpenPilot Mini CC3D board comes in a high quality, protective case.
• Horizontal pin

Specs:
Size: 28x21x9mm
Weight: 4g

Package includes:
1 x Mini CC3D Flight Controller
1 x Set of Cables

  • SKU 571000053-0
  • Brand Other
  • Capacity (mAh) -
  • Shipping Weight 22.0000
  • Packaging Length 100.00
  • Packaging Width 10.00
  • Packaging Height 80.00
  • Mini CC3D & Nano N32 FC
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

I mounted this little board in a crusader 130 frame with some 1306 3500kv motors and 3035 x3 props. After downloading librepilot, updating the firmware and configuring my radio/quad, I took it for a spin with the default settings. It flew surprisingly great! The only downside so far is that the boot pins are not exposed in the board, meaning no flashing with betaflight unless you have a STM link. Still a great board for small copters or even helis.

playlist_add_check Overall:
trending_up Value:
verified_user Quality:

I mounted this little board in a crusader 130 frame with some 1306 3500kv motors and 3035 x3 props. After downloading librepilot, updating the firmware and configuring my radio/quad, I took it for a spin with the default settings. It flew surprisingly great! The only downside so far is that the boot pins are not exposed in the board, meaning no flashing with betaflight unless you have a STM link. Still a great board for small copters or even helis.

Plugged and supplied it and rhino update was done in a few moments. great product, i like librepilot and its options.
i run this one on a race quad, and the settings can be adjusted by fine steps. there are a lot options with this flight controller and a wide community with good support. for basic settings there are a lot of youtube vids too. will buy it again for next multirotor.

trending_up Value:
verified_user Quality:
playlist_add_check Overall:

Plugged and supplied it and rhino update was done in a few moments. great product, i like librepilot and its options.
i run this one on a race quad, and the settings can be adjusted by fine steps. there are a lot options with this flight controller and a wide community with good support. for basic settings there are a lot of youtube vids too. will buy it again for next multirotor.

ordered this one for fixed wing- 4 flap wing- to have some differet stabilisation options during thermal flights- offeres 6 setups that you can change via TX. very very good hardware- and you need some time to work with it as it offers lots of functions, nothing to be compared with a 3 axis flight stabilisation

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

ordered this one for fixed wing- 4 flap wing- to have some differet stabilisation options during thermal flights- offeres 6 setups that you can change via TX. very very good hardware- and you need some time to work with it as it offers lots of functions, nothing to be compared with a 3 axis flight stabilisation

Nothing I can do with this board. Librepilot will not update. It downloads and then times out at the bootloader stage. This tells me that the board does not have a bootloader. In addition to that there are no boot pads like on the cc3d. That means there is no way for me to load a bootloader.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Nothing I can do with this board. Librepilot will not update. It downloads and then times out at the bootloader stage. This tells me that the board does not have a bootloader. In addition to that there are no boot pads like on the cc3d. That means there is no way for me to load a bootloader.

If you directly hookup a satelite receiver to the main or flexi port (e.g. Spektrum SPM9645 <4g) you end up with a receiver flight controller solution that
weighs 8g in total.

Since the SPM9645 runs on 3.3V you need to add a 3.3V regulator (e.g. AMS1117) - the CC3D runs on 5V.

The only drawback is - if you wan to have
satelite receiver GPS OSD current measuring module - there aren't enough connections.
If you want/need all of the above go with the CC3D revolution instead.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

If you directly hookup a satelite receiver to the main or flexi port (e.g. Spektrum SPM9645 <4g) you end up with a receiver flight controller solution that
weighs 8g in total.

Since the SPM9645 runs on 3.3V you need to add a 3.3V regulator (e.g. AMS1117) - the CC3D runs on 5V.

The only drawback is - if you wan to have
satelite receiver GPS OSD current measuring module - there aren't enough connections.
If you want/need all of the above go with the CC3D revolution instead.

surprised at the size very small very stable will be using this board for more projects only thing make sure your using a cord that does more then charge a phone or board will not connect to computer love this controller will be getting more

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

surprised at the size very small very stable will be using this board for more projects only thing make sure your using a cord that does more then charge a phone or board will not connect to computer love this controller will be getting more

I could not get serial connection via Openpilot GCS to this board, tried different firmwares, bootloaders and GCS but no serial connection. Then I flashed cleanflight for CC3D and it works :) I see no reason at all to buy the twice as expensive NANO N32 board, that one doesn't even have onboard FTDI (USB) which I find very usefull

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I could not get serial connection via Openpilot GCS to this board, tried different firmwares, bootloaders and GCS but no serial connection. Then I flashed cleanflight for CC3D and it works :) I see no reason at all to buy the twice as expensive NANO N32 board, that one doesn't even have onboard FTDI (USB) which I find very usefull

Fantastic capability at an amazing price. The Openpilot GCS makes it easy to set up and optimize for most options. The CC3D Atom might be a better choice to drive servos on flybarless helicopter.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Fantastic capability at an amazing price. The Openpilot GCS makes it easy to set up and optimize for most options. The CC3D Atom might be a better choice to drive servos on flybarless helicopter.

Customer files
custom PDB Download [261]
33CDMini Layout Download [132]
Layout Download [562]
Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!

Combine Essential Items and Save