OrangeRX MicroRX3S Micro Flight Stabilizer with integrated OrangeRX DSMX and DSM2 compatible 4CH 2.4Ghz receiver is perfect for indoor and micro models.
By eliminating the need for using a separate receiver in your model, valuable weight and space can be saved (always bonus in any model) and a neat installation is a breeze. Add a flight stabilization system with remote gain control into the mix and the MicroRX3S becomes a must-have item for just about any small model!
The MicroRX3S provides support for V-tail and delta wing models, and also offers a remote gain control feature that can be controlled via your transmitter's AUX channel for fine tuning your setup.
Utilizing a single high precision 3-axis MEMS gyro, the MicroRX3S is capable of stabilizing flight on just about any fixed wing aircraft, smoothing out the effects that turbulence has on your model.
The MicroRX3S 3-Axis Flight Stabilizer has been designed specifically for use in micro models and weighs a mere 10g! The size has been perfectly matched for use with our own Durafly Telemicro, but is equally compatible with any other micro model using 3 pin Micro Molex connectors with 1.25mm pin spacing.
This unit is simple to install and use, and with the adjustable gain settings pre-set to 50% (mild stabilization) is ready to use just as it comes. Each channel (Ail/Ele/Rud) is independently adjusted so that precise tuning can be applied to your model.
Because we design, test and manufacture these units completely in-house (from 3D/2D drawing to materials sourcing, final assembly etc.) we can completely control production and ensure product consistency from design right through to shipping the product to you. Also, the removal of middle-men has meant we can drive better value to the market and retail these units at factory (our) prices!
• Perfect fit for all micro models
• OrangeRX DSMX & DSM2 compatible 4CH 2.4Ghz integrated receiver
• Micro Molex 3 pin connectors with 1.25mm spacing
• Capable of stabilizing flight on just about any fixed wing aircraft (including V-tail/Delta models)
• Remote gain feature that can be controlled via your transmitter's AUX channel
• Supports 3D flight without undermining stability
• Independent gyro gain adjustment for aileron, elevator and rudder
• Easy-to-access gyro reversing switches on front of unit
• Compact and lightweight design
• Compatible with Spektrum and JR DSMX & DSM2
Integrated Receiver: OrangeRX DSMX/DSM2 compatible 4CH 2.4Ghz
IC: Atmega 168PA
Gyro: 3-Axis MEMS
Input Voltage: 4.8-6.0V
Signal to Servo: 1520us
Servo/ESC Connection: Micro Molex 3 pin with 1.25mm spacing
Size: 46 x 19 x 10mm
*Note: User manual available here
1) This is not a Spektrum DSM2/X product, nor is it a copy of a Spektrum DSM2/X product.
The Spektrum and DSM2/X brand is a trademark of Horizon Hobbies USA.
2) This is not an underground black market fake Spektrum product. OrangeRx quality is guaranteed.
Not used yet, but could be usefull. unfort it wants servos with Mini Molexpretty small - gyro is working fine - used with Devo 6 Deviation FW - LIKEBought this for a small airplane. Binded just fine. Now to order some servo connector adapters when they arrive in stock. Howlin HobbyKing Batman! They have everything!I am using these small and smart micro receivers with 3 axis gyro in Spirit Mini sport Glider, and Bigger receiver with Gyro on Skyfun Jet, AXN Glider and scratch build Depron Jets. I found them to be very useful for stabilizing the models, specially in windy conditions. On bigger receiver it's true that the compensation is too much and in micro Rx, it's just enough for the Ailerons and a bit low on Elevator and rudder and that's sufficient for my requirements. A little more compensation on elevator and rudder is welcome.
If you setup these Rxs properly, they work very nice, offering very satisfying flying experience. Planes will be blown around and feel out of track when stabilizer is switched off. I was pleasantly surprised when I found that I can adjust the gain in the remote in the micro Rx, but with bigger Rx, it's on/off only.
Remember, these are stabilizers only, not designed to keep the plane on course since there is no auto-level feature. Auto level as an option if it's added in future, it will be great.
It would have been better with standard JR/Futaba connectors.Not enough compensation for rudder and elevator corrections even when turned up to maximum. Aileron correction is not bad. This small stabilizer is designed for micro/small aircrafts which tend to move around a lot in the wind. Therefore, you must compensate a lot to counter the wind effects. Unfortunately this RX3S does not do enough. Also, it's just a stabilizer, not a gyro, so it does not keep the plane on course.
RX3S manual download now [996kb] recever download now [698kb] No File Name download now [159kb] microstabi 6.2g download now [1.07Mb] Binding and power through the same plug download now [431.84Kb]