The Phantom is the newest addition to our range of First Person View (FPV) models. It is a great flyer with very predictable handling qualities, excellent stability and lots of wing area to cope with additional loads for FPV use.
The Phantom features tough EPO construction with molded in camera bays - one forward looking just under the nose and another mount in the top of the canopy with a plywood support pre-installed. Speaking of pre-installed items, the servos, 900kv outrunner motor and 30amp speed controller are also installed ready to go.
Assembly of the airframe is very simple, literally four glue joints required - foam glue is also included!
This model is capable of flights in excess of 30 minutes on a 3s 4500mAh lipo and the space under the canopy is cavernous! There is plenty of space for your choice FPV gear.
• Ultra tough EPO construction
• Ultra stable flight performance
• Excellent FPV platform
• 30 minute plus flight duration on 4500mAh 3s lipo
• Easy to Hand Launch, Easy to Land
• Stable Handling at Low and High Speeds
Flying Weight: 900g
Molded EPO foam parts
2 x 9g servos
900kv Brushless Outrunner Motor
2 x propellers (9 x 6)
Carbon Fiber Spars
4 Channel Radio (with delta mixing)
4500mAh 3s Lipoly battery
Muito bom e estvel, o motor da verso PNF no super potente mas suficiente.
As Hlices fornecidas no kit so lixo,Clocked up a few hours with the FX-61 now. Great fun to fly, looks awesome and great flight times. Unfortunately though, the flight footage is not as good as with my Bixler 2 due to a constant oscillation in the airframe. Its not jello, i'm using an anit vibration plate, but a constant flapping that makes the video hard to watch. I now see this in other video from other FX-61 pilots. I assume that additional reinforcing of the airframe is needed. Needs a lot more correction to keep flying level compared to the conventional fixed wings with vertical and horizontal tail stabilisers. Perhaps I'll look into a larger version of the Bixler type plane like the sky eye.Its fantastic plane. Great for FPV. There is a big pleace inside of plane what enogh for Futaba 14ch receiver, esc, joystic what is for OSD Menu and 4,5 Battery. I made a plate by wood what i putted with glue above the battery and i putted OSD autopilot onto wood.
Everything fine with this modell.
I recommend to everybody who hasitate what is better.
I received my wing on the 5/12/2013. It was will packed well and in perfect condition. Built it on Sunday morning and installed FPV gear then took it for the maiden it on Sunday evening. She is no speed demon top speed 70kph but is VERY VERY efficient and flies very stable win NO nasty surprises at all. Total flight time with 1X 5000mah 3s for motor and 1X 1000mah 3s for FPV gear was 40min with mixed flying habits. Would give 6 stars if it was possible as it is my new favorite FPV platformThis is one of the best fpv wings I've tried so far, highly recommendedJust bought the phantom fpv through the Australian warehouse and received it without the right wing - beware, it may be a batch issue.This is a really nice model for FPV. It is very stable in flight, has sufficient power when running on a pair of 2200mAh 3S batteries using the supplies motor and prop. It is very quick and easy to build. Surface finish is super slick. On the down side the servo horns are flimsy and break off easily, I suggest replacing them as they tend to break while loading the model into the car ...... A 10x7 APC Prop will give better penetration on windy days, while not sacrificing too much in duration. Strap the batteries in with a loop of velcro going through the bottom vents, or else they can eject out the top of the model(even when stuck to the bay with velcro).Have flown the Phantom about 50 times now, and I am very happy with it. Super stable and predictable. The setup is very light but will get thrown around a little in the wind.
FPV video over the beach
http://youtu.be/8uI8GrLiQTMBuy kit model. stock motor and esc not for fpv. stock motor can not payload well with 3s, also 4s. in the air not problem but launching with stock motor 4s and gopro and autopilot systems is big problem. it comes with these systems and 5000mah compact lipo 1450gr. buy ld3730 1000kv 3s-4s (need to buy extra acceserios) or 3015a 1000kv 3s motor. buy redbrick 50a and program it to brake (second beep to lipo, third beep to brake on) , 10x7 prob. these setup with 3s can push 1800 gr not fully battery. also stock esc can be used if you will just cruise and not need power but i suggest red brick50a. also recomended trust 55a but red brick much lighter.3 star for electrnics 5 star for the others.
stock motor can not with 3s, also 4s. in the air not problem but launching with stock motor 4s and gopro and autopilot systems is big problem. it comes with these systems and 5000mah compact lipo 1450gr. buy ld3730 1000kv 3s-4s (need to buy extra acceserios) or 3015a 1000kv 3s motor. buy redbrick 50a and program it to brake (second beep to lipo, third beep to brake on) , 10x7 prob. these setup with 3s can push 1800 gr not fully battery. also stock esc can be used if you will just cruise and not need power but i suggest red brick50a. also recomended trust 55a but red brick much lighter.
No File Name download now [10085kb] Little modification for FPV download now [2040kb] 507495604X1053396X38.txt download now [4kb] 507495604X1053396X1.txt download now [4kb] Phantom mit Boscam HD Camera download now [453kb]