Register

Product Finder

Settings

Useful links

Live Chat
 
[["US","AU","GB","DE"]]
Register

TR 28-45 3600kv Brushless Inrunner (WaterCooled)

TR 28-45 3600kv Brushless Inrunner (WaterCooled)

Discontinued Product

Please continue searching for a similar product.
Rating:
Stock:
OUT OF STOCK
Weight:
150 g
SKU:
TR28-45-3600WJ
Product
Description

TR 28-45 3600kv Brushless Inrunner (WaterCooled)
Kv: 3600rpm/v
Required ESC: 40A
Voltage Range: 6-15v
No Load Current: 1.5A
Mas Load: 45A
Max Power: 300W/60S
Weight: 149g
Shaft: 4mm
Standard size mounting holes enable the motor to be installed in a large range of motor mounts.

Motor has an inbuilt water jacket.

 

Product
Specifications

Additional Information

  • SKU:
    TR28-45-3600WJ
  • Brand:
    N/A
  • Shipping Weight(g)
    150.00
  • Length
    0.00
  • Width:
    0.00
  • Height:
    0.00
  • Kv(rpm/v)
    3600.00
  • Max Currents (A)
    45.00
  • Power (W):
    300.00
  • Length B (mm):
    59.00
  • Can Length D(mm)
    34.00
  • Max Voltage(V)
    15.00
  • Shaft A(mm):
    4.00
  • Unit Weight (g):
    149
  • Diameter C(mm)
    35.00
  • Total Length E(mm)
    73.00
  • Resistance (mh):
    0.00
Community
Discussions
Rate&
Review

Write Your Own Review

Only registered users can write reviews. Please, sign in or sign up

verified_user Quality
trending_up Value
playlist_add_check Overall
After a 2 minute journey with 11.1 LiPo on the water the boat stopped.
After a fast swim i smelled the bout, it was hot and did not smell good at all.
I was hoping it was the speed controller but NOOO the engine is fried.

I put it in wit a Prather X440/3 movie here.
Even the wires into the motor have melted :( so i realy dont se how this motor can cope with 15V
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Just hooked up this motor to an Aquastar 90A ESC. Bench testing the motor with zero load it draws massive current and gets very hot. Shaft turns freely and ESC is set to auto. I think my motor must be faulty so I will return it for a replacement. Really looking forward to getting this boat up and running.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
GREAT POWER FULL MOTOR It make a high power without high temp issue I apply with modify DEEP V boat ( CHINA BOAT) 24" with 80A ESC on 4 S battery very fast""
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Very good engine for a 60cm boat, i use this with a LIPO 2S 5000mah, and a K31mm graupner prop, the wattmeter give me 50amp. ( /-15min), the engine and the esc keep cool.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
good for my boat, 50W without any charge
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Just bought one,
Had one before and must say it is a great little powerfull motor.
With the right ESC and prop It will not get hot and deliver a lot of power.
I had it in a Blaze EP boat and it ran about 65 kmph.
Now I will plce it in a sword mono I of 60 cm ...........
Like this motor!!! full stars for it
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
kjbdsfv igg iugisdc ug idsv ggiug mhndds iuhvcadbbkx cd uvcbakjbiuhdsv uiuh jbdasvk iuhdiua
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I bought 2 of these motors for the HK F1 Hornet. I also used the HK marine 60amp ESC. This is a great combo, running a 3s5000maH battery. The boat is now super fast (approx 70km/hr), be careful as the boat flipped on my 1st run, and had to re-adjust the outboard leg. The ESC and motor do get warm, but not hot. I run a 42mm prop.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Ok so I got these motors in about two to three weeks time as usual.



On first look they look nice no problem there, seems to hold watter, conectors are good...



Then i tested them (no load for now) with 40A superbrain ESC wiith half charged 3S LiPO and I got: 5,8A no load current at 11,5V spining at about 41400RPM



They're not runing as smoth as i hoped they would - i'm a bit woried about berings failing



Other than that I will be using it as Speed600 replacement/upgrade - the size is about the same at only 75 of weight. The only thing wrong here is that the mounting holes dont match - they are 16mm and 19mm apart but no big deal. Screws are M3



All in all i think they're all right, but the true test is still to come as I'm still building me self designed twin drive catamaran
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
TR28-45-3600w- i heard a bad noise and pulled the endbell off and the cylinder inside had flaked the covering about the size of a pencil eraser and shut down completely. Now can there be a replacement cylinder for this motor or not, thanks for your time and patience. retoabcr
verified_user Quality
trending_up Value
playlist_add_check Overall
View all reviews
Upload
Videos
Upload video
Upload
Files

Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.