-
Product
Description -
Turnigy 5A SBEC is an advanced switching DC-DC regulator which will supply a constant 5A. It works with 2 - 7 Cell Lipoly pack and supplies a constant 5 or 6v to your receiver and is interference-free.Specs:Type: SwitchingInput Protection: Reverse polarity protectionOutput (Constant): 5v/5A or 6v/5A
Input: 8v-26v (2-7cell lipo)
Weight: 18gSupplied with full instructions. -
Product
Specifications -
Additional Information
-
SKU:
SBEC-26V
-
Brand:
N/A
-
Capacity (mAh)
No
-
Shipping Weight(g)
37.00
-
Length:
110.00
-
Width:
13.00
-
Height
105.00
-
SKU:
-
Community
Discussions -
-
Rate&
Review -
I bought 5 of this BECs and I am very disappointed. I tested everyone, but more than 3 Amps are not possible. On 3 Amps the output voltage drops to 3,5 Volt and the BECs get very hot. I would declare this BEC as a "2,5A, max 3A" BEC, not more.Be careful with this BEC. I had to add extra capacitor at the output side otherwise
output voltage went down when current was about 2 amps.Have running some of this. Works perfect. It easy feeds 6pcs of powersucking 9g Digi Servos in a 2,5m Glider without making some electric trash. I'm happy with it!!works great and its small and light weightGreat use for power up CDI and RXWorks well and the wires are a decent length to begin with so no fussing around trying to get power to it from the main battery. I chose to power it separately from a 2s 1000mah pack for use in one of my large EDF models.Very good and stable voltage.This powers a Raspberry Pi 1 Model B just fine.
But it won't allow a Raspberry Pi 2 to boot - it continually tries to boot but browns out after a second or two, and then repeats. This Pi was tested good using a USB power supply both before and after the test with the SBEC.
Both Pis were tested with a 5200MaH battery, with the SBEC set to 5V and connected to the 5V/GND GPIO pins of the Pi (via a Pi Cobbler and breadboard).
Here's the battery used: http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=84097I wasn't happy powering 6 servos and telemetry unit off the BEC on a 30A ESC so added one of these. Works perfectly.Been using these for years. Have several, very reliable and easier to use than old nimh. -
Upload
Videos -
Upload
Files -
Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!
Customer filesOutput voltage shape on oscilloscope download now [65kb] Turnigy_5A_(8-26v)_SBEC_Manual download now [44kb] bec download now [1009kb]
Sign in
Register
Sign in / Register
OR
or
Register
-
-
-
ACCESSORIES
- EDF Systems & Parts
- Wheels/Landing Gear/Retracts
- Spinner/Adapters
- Propellers
- Wires & Connectors
- Heat Shrink / Shrink Tube
- Flight Stabilization Systems
- Horn/Hinge/Clevis
- Screws, Bolts, Nuts and Fasteners
- Covering Film
- Decal Sheets
- Glues, Lubricants & Tape
- Night Flying Accessories
- Push Rods
- Tube, Rod, Carbon Fiber & Glass Fiber
- Pilots
-
-
-
TELEMETRY & FPV
-
-
-
-
-
POWER SYSTEMS
-
-
-
-
BOAT ACCESSORIES
-
-
-
POWER SYSTEMS
-
-
-
-
POWER SYSTEMS
-
-
-
-
DIY & ELECTRICAL ACCESSORIES
-
-
-
FPV, AERIAL VIDEO & TELEMETRY
-
-
Show Filters
All Categories
Product Finder
Settings
Useful links
-
-
-
ACCESSORIES
- EDF Systems & Parts
- Wheels/Landing Gear/Retracts
- Spinner/Adapters
- Propellers
- Wires & Connectors
- Heat Shrink / Shrink Tube
- Flight Stabilization Systems
- Horn/Hinge/Clevis
- Screws, Bolts, Nuts and Fasteners
- Covering Film
- Decal Sheets
- Glues, Lubricants & Tape
- Night Flying Accessories
- Push Rods
- Tube, Rod, Carbon Fiber & Glass Fiber
- Pilots
-
-
-
TELEMETRY & FPV
-
-
-
-
-
POWER SYSTEMS
-
-
-
-
BOAT ACCESSORIES
-
-
-
POWER SYSTEMS
-
-
-
-
POWER SYSTEMS
-
-
-
-
DIY & ELECTRICAL ACCESSORIES
-
-
-
FPV, AERIAL VIDEO & TELEMETRY
-
-
Cart is empty Make it look better :)
Total $0.00 0 item(s)
Product Finder
-
Lipo -
Motor -
Servo -
Propeller
Most relevant matches are shown. Click Search for more items
