The Turnigy Accucell 6 50W Balance Charger utilises quality FET's and resistors to accurately balance and charge LiPoly, LiFe, LiHV, NiMH, Nicd and Lead Acid batteries.
If you are looking for a charger for your Bolt batteries this unit is perfect as a low cost, go anywhere solution. The Accucell-6 will handle LiHV/LiPoly/LiFe up to 6S and NiMH/NiCd up to 15S and shows individual cell voltage throughout the charge cycle.
The intuitive menu system means charging and cycling is an easy process and can be done quickly and accurately. And because this is a 12v DC charger you can power it up at the field using a 12v car battery or at home with a 12v power supply.
It is also able to connect this charger to your PC using a USB cable (not supplied) so you can monitor pack voltage, cell voltage and other data through real-time graphs during charging. You can also control charging and update firmware from "Charge Master".
Also included with the Accucell-6 is an input lead and XT60 equipped charge leads with optional alligator clips for maximum versatility.
There are several chargers now entering the China market that look similar to the Accucel. These chargers are produced with cheaper FET's and are unfortunately much less accurate and very unsafe. There has been reports of the copied chargers over-charging packs and not balancing correctly.
The Accucell-6 is the first charger in the market with this PCB layout Circuit design. Any charger with the same circuit diagram is most definitely a copy. We have tested the copied chargers ourselves, their componentry is of a very low quality and the manufacturing company that has produced the copy has used a process of duplicating our CPU(MCU)'s hex file and flashed a similar chip(MCU) to produce a similar product. This means they do not have the original code and therefore cannot bug-test (QC) or update the charger at any point. Our chargers have CE and RoHS certification, proving their safety.
Plus, thousands of customers the world over have used our chargers with excellent results.
Your batteries are expensive. We understand this and that’s why we will not carry low-quality charging devices.
Trust only in TURNIGY® quality charging devices.
• Microprocessor controlled
• Individual cell balancing
• LiHV, Li-ion, LiPoly and LiFe capable
• Ni-Cd and NiMH capable
• Delta-peak sensitivity (NiMH/NiCd)
• Lead Acid capable
• Large range of charge currents
• Terminal Voltage Control (TVC)
• Lipo Battery Meter
• Battery Internal Resistance Meter
• Store function, allows safe storage current
• Time limit function 1~720 minutes
• Temperature Cut-off (20-80 degree Celsius/68-176 Fahrenheit)
• Input voltage monitoring. (Protects car batteries at the field)
• Data storage (Store up to 10 packs in memory)
• Battery break in and cycling. (1-5 cycles)
Input Voltage: 11~18v
Circuit Power: Max Charge: 50W / Max Discharge: 5W
Charge Current Range: 0.1~6.0A
Balance Cells: 2-6 cells
NiMH/NiCd Cells: 1~15
LiHV /LiIon/LiPoly Cells: 1~6
Pb battery Voltage: 2~20v
This charger has a JST-XH balance charge plug, which makes it compatible with Zippy, HXT, TURNIGY and any pack with a JST-XH adapter.
1. Accucell 6 50W Charger
2. Alligator clip input lead
3. XT60 with Banana connector charging Cable (340mm)
4. XT60 to Alligator clip charging cable (180mm)
Note: Power supply, power source cable, temperature sensor and USB cable are not included.
I've used this now for 5 months with almost daily use charging, 2S, 3S, 4S, 5S, and 6S lipos with no problems. It's quiet so you have to listen for the beep when the charging is finished. I prefer a quiet beep instead of an annoying loud beep. It stays cool also, barely warm. I am happy with the purchase. The resistance meter is great for checking old batteries (those with nearly a hundred cycles) to see if they are holding up or losing capacity.Great charger. I had a Imax B6 clone but needed a LiHV capable charger. Not much more expensive than a B6 but much better.
I really like the battery internal resistance tool.Using to parallel charge with the laptop and works wellJust got my new Accuell-6 50W charger. I'm very satisfied with its quality - it is built very precise and is working accurately - I've already performed few charging cycles of my LiPo batteries and verified voltages displayed on the LCD with a good multimeter. The device is very usable, very intuitive for anyone who dealt with any type of computer-type chargers. Good hardware for good money. I recommend it.Received this charger, ordered only to charge my 3s LiHV batteries. It`s doing his job very well, charging end sound a bit to quiet. A good charger for low-middle budget .Hello,
This is my second charger of the same type. They evolved in the right direction.
It is smaller. Software enhanced with all such kinds of batteries. Function vey well and safe. .
me and my friend had a trouble whith this charger but replacement was sent fastThis is a great little charger for the price, it does a good job on lihv, and normal lipo, and it is fine for nimh like a standard taranis pack...Overall I am stoked with it, and I have a fleet of b6, b6pro, imax, and b405 pockets....this one is my favorite so far..I only charge 3-4s lipo and lihv to keep things clear.good charger works fast and very decent. I returned the item. due to it not being compatible with my battery
This little charger is awesome! I like having a small charger that i can throw in my quadcopter case for traveling. Combined with the mini 7A power supply this is the ultimate package. I originally had a B405 pocket charger which fried so I opted for this as its replacement. Pro's of the Accucell 6 over the B405: discharging, storage mode, all the adjustments of a full size charger, LiHV charging, temp sensor port, PC link, fan, and much more. So yeah definitely worth the extra $10. Approx. dimensions 115mm x 80mm x 30mm
PC software download now [1995kb] PC software download now [1995kb] PC software download now [1995kb] PC software download now [1995kb] PC software download now [1995kb] PC software download now [1995kb]