-
Product
Description -
Turnigy SK3 Motors are the next leap forward in motor quality and design. We instructed the engineers to source the best quality magnets, bearings and materials available to them and develop a motor that would not only rival, but surpass the quality of many leading motor manufactures on the market today.
The result is an efficient, high caliber motor using quality double shielded bearings, sintered Neodymium magnets and a string wound stator ensuring an accurate and consistent winding each and every time.
The Turnigy SK3 motors are suited to modelers who are seeking a quality brushless motor without compromise.
Specs.
Turns: 12T
Voltage: 2~3S Lipoly
RPM/V: 1040kv
Internal resistance: 0.075 Ohm
Max Loading: 28A
Max Power: 335W
Shaft Dia: 3.175mm
Bolt holes: 16mm & 19mm
Bolt thread: M3
Weight: 80g
Motor Plug: 3.5mm Bullet Connector -
Product
Specifications -
Additional Information
-
SKU:
SK3-2836-1040
-
Brand:
No
-
Shipping Weight(g)
156.00
-
Length
110.00
-
Width:
45.00
-
Height:
80.00
-
Kv(rpm/v)
1040.00
-
Unit Weight (g)
80
-
Max Currents (A):
28.00
-
Resistance (mh):
75.00
-
Max Voltage(V)
11.00
-
Power (W)
335.00
-
Shaft A(mm):
3.18
-
Length B (mm):
40.00
-
Diameter C(mm)
28.00
-
Can Length D(mm)
23.00
-
Total Length E(mm):
54.00
-
SKU:
-
Community
Discussions -
-
Rate&
Review -
Perfect much for my Mini Talon with a 4s battery on 8X6 prop or 9X6 on 3s ;)I'm using this motor 2836-1040KV on my new MX2 3D EPP 955mm ARF in combination with a Turnigy Plush 40A, TURNIGY GRAPHENE 1300MAH 3S 45C and WS Style Slowfly Propeller 11x4.7. Great power and great performance for almost 5 minutes of hot 3D flying!
Really satisfied.Great motor works well as a replacment for the bixlerThis motor is crap!! My setup is a 50amp ESC, nano-tech 1300maH 45-90C discharge and 10x4.5 prop. I put it at full throttle and not even a minute in the motor burned up. For those that said they ran a 10x7 with no problem, I find that hard to believe. I have had bad luck with the quality of electronic parts from Hobby King. You get what you pay for.Gegenber dem Vorbild Hacker A20-12XL V2 (den ich schon mal besa, allerdings in der Version V1, aber verkauft ist verkauft...) hat der Motor 2g Mehrgewicht (forget it!). Der Ri von 75mOhm (wie Original) wurde nicht erreicht, lt. meinen Messungen sind es 90 mOhm. Die 1040 rpm/V werden auch nicht erreicht, im typischen Spannungsbereich von 10-11V sind es 1140 rpm/V. Immerhin, der Leerlaufstrom von 1,2A wird von Hacker bei 8,4V genannt, ich habe dies erst im Bereich von 10,8V erreicht, das spricht fr die Qualitt der Bleche, insbesondere da die kV etwas hher ist! Angesichts des viel geringeren Preises geht das fr meine Bedrfnisse (Einbau in den eigentlich leichten Hoellein Inside (SPW 2,9m) vllig in Ordnung, aber als Inside 3.7 oder 3.8 (noch nicht fertig) mit etwas Mehrgewicht (wie viel blo?!) muss kann sehen.Pura potencia estos motores!!Motor ist top. Mit SLS-1250/40C 3S Lipo, an Aeronat Light 10x5 = 28A bei 11,6V => 325W..! Vision-EP (870mm), 642g, Schub max: 1260g, also senkrecht ohne Ende! Temp, bei normalem Kunstflug, 5min. max 50*C. Also passt optimal, l*uft leise und sauber rund! Perfekt.kleines motrchen. werde es mit 10x6 klappschraube betreiben. 11x6 geht grenzwrtig mit 33A wurde im rc-network gemessen.The motor is very good and very powerful, the problem is the X-mount: it's to thin and fragile.
It's the same motor mount you get for those smaller motors, adequate for a thrust of ~300g, but this thing is rated 330W: my X-mount has bended 2 times and finally broke.
Do consider that the motor is quite heavy, the cables are quite fragile (one broke inside of the motor, a real nightmare to repair as you can not completely dismount the back) and finally the motor shaft is quite thin for such a power rating. So also consider a 3530 SK3 (bigger shaft and stronger mount), or maybe a cheaper / lower KV / lighter 3536 Turnigy.Minus: My motor came unbalanced from the factory (I could feed it's movement during rotation) and shaft bent first time it touched the ground. It's my 3rd SK3 so I'm bit surprised and disappointed :(
Plus: It runs cold under load and bearings are nice and quiet. Full set of accessories in the box.
-
Upload
Videos -
Upload
Files -
Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!
Customer filesDrawing download now [89.96Kb]
- acc
-
-
Turnigy Aerodrive SK3 2836 Series Replacement Shaft Set
$1.14 -
Turnigy Aerodrive SK3 - 28-XX Spare Accessory Pack
$5.22 -
T-Prop Adaptor Set for SK3 Motors (Direct Bolt)
Special Price $4.99
You save $5.07
Was $10.06
-
Combine
essential items and
Related Products
T-Prop Adaptor Set for SK3 ...
Special Price
You save $5.07
Was
