- Product
Description -
Turnigy SK3 Motors are the next leap forward in motor quality and design. We instructed the engineers to source the best quality magnets, bearings and materials available to them and develop a motor that would not only rival, but surpass the quality of many leading motor manufactures on the market today.
The result is an efficient, high caliber motor using quality double shielded bearings, sintered Neodymium magnets and a string wound stator ensuring an accurate and consistent winding each and every time.
The Turnigy SK3 motors are suited to modelers who are seeking a quality brushless motor without compromise.
Specs.
Turns: 12T
Voltage: 3~4S Lipoly
RPM/V: 1400kv
Internal resistance: 0.021 Ohm
Max Loading: 40A
Max Power: 590W
Shaft Dia: 5.0mm
Bolt holes: 25mm
Bolt thread: M3
Weight: 110g
Motor Plug: 3.5mm Bullet Connector - Product
Specifications -
Additional Information
-
SKU:
SK3-3536-1400
-
Brand:
Turnigy
-
Weight(g)
212.00
-
Length
110.00
-
Width:
45.00
-
Height:
80.00
-
SKU:
- Community
Discussions -
- Rate&
Review -
I bought it for my fpv 1900mm skywalker.I lot of power with 3s battery and 9x6 prop!I fly with 12000mah batteries!Went with HK recommendations of motor ESC and prop for Bela Trike. Watched the motor go up in flames on first run up to full speed.I think it was just a fluke but I am not very experienced at brushless motors yet.motor cremat en 2 minuts. un desastre. una 11x7 i 4s. tindria que aguantar de sobres.
si algu se li ocurreix comprar'ho. pala petita.WOW!!! What a Motor!!! Put a 9x6E (PRODUCT ID: TGS9x6E) on it with a 2200ma 3 cell and pulled an Amazing 398.5 Watts at 38.92 amps and 11.48 volts. Have it installed in a Multiplex Dogfighter with a weight of 1.6lb/750g. This plane should skyrocket. I'm expecting to fly most of time at half throttle and still have a speed demon. A very quiet motor with a very smooth range of power. I really like the power curve as it accelerates. I will only by Turnigy SK3 motor in the future. The quality is certainly built in.One tuff motor it has heaps of grunt in my sky surfer but a good replacement for my asw28 adds the punch to climb outsI have this motor in a Stryker 27Q using a plush 100A ESC on 4S 2450mAh and a 8x6 APC prop and the power is insane. Hand launching the plane is so easy now because of the instant torque. And the top speed is so fast I just limit it to short controlled bursts so I don't loose control. This is one impressive little motor, make sure you get the adapter if you are going to run it as a pusher.Great motor. I use it in my HobbyKing EPP FPV plane and it has got power. I use this motor with HK SS Series 50-60A ESC (make sure you buy a separate UBEC with that ESC), 10x4.5 SF prop and a 3s 5000mAh 20C Turnigy battery. I think it's a great setup.I put this SK3 motor on a Parkzone Bf-109 foamy with a Turnigy Plush 40A speed control. I am using a 2-bladed 9X6 prop. My battery is a Turnigy 3000mAh 3S. I had to dial the ATV back on the max throttle to keep below the 40A limit. The model is super fast with unlimited vertical. I will definitely be buying more SK3 motors.Really good Motor. Comes in nice box! Great finish!This is a great motor. With a 3s 2200mah, a 9x6 prop, 40a hk brushless esc this motor can make my 36" contender go vertical at 6000'. Motor was barely warm after a spirited flight. I would recommend this motor to anyone looking for a high quality motor. Its about the same physical size as an NTM 35-30 1400kv motor but with much more power. The NTM couldnt handle the 9x6, but this motor does the job. - Upload
Videos - Upload
Files -
Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!
Customer filesSK3-3536(DT3013-14P) MOTOR (1) (edited).pdf download now [121.08Kb]
- acc
Combine
essential items and
