Turnigy AquaStar 200A Watercooled Sensorless High Voltage 6-12S (ESC)
Turnigy AquaStar 200A Watercooled Sensorless High Voltage 6-12S (ESC)
Copy and Share the Below URL
The all new Turnigy AquaStar 200A sensorless ESC, ultra fast microprocessor controlled and extremely low resistance circuit and chip design, water-proofed PCB, and aluminum water cooled heatsink for better thermal dissipation. These are just some of the features in the new super cool Turnigy Aquastar range of brushless boat speed controllers. The Aquastar range of brushless ESC's are a high performance speed controller capable of regular competition use.
Programmable Settings:
Reverse Type: Reverse lockout, forward only, forward / reverse*
Motor Direction: Normal*, reverse
Reverse Amount: 25%, 50%, *75%, 100%
Starting Power: Low, normal*, high
Voltage Cutoff: Lipo 3.0V per cell, NIMH 40% of power up voltage
Motor Timing: Low / normal / high*
*Default setting
Specs:
Motor Type: Brushless, sensorless motors only
Input Voltage: NIMH 15-33 cell, Lipo 6-12s cell
Operation Current: 200A Cont, 250A peak
BEC: No BEC, seperate BEC required
Thermal Protection: 95°C
Lost RX Protection: Delay 0.5 second
Dimensions: 115 x 50 x 31.5mm
Weight: 290g
Note: Standard software is suitable for 2 pole motors. Customers using 4 pole or higher should use the 4 pole firmware set under files tab and set acceleration to low.
-
SKU 9192000112-0
-
Brand AquaStar
-
Capacity (mAh) -
-
Shipping Weight 530.0000
-
Packaging Length 200.00
-
Packaging Width 65.00
-
Packaging Height 105.00
Hello i by an Turnigy AquaStar 200A Watercooled Sensorless ESC, and somebody can tell me which BEC i need ?
Hello i by an Turnigy AquaStar 200A Watercooled Sensorless ESC, and somebody can tell me which BEC i need ?
I bought 2 speed controller 2 engines and a programmeringsbox
Programmeringsbox not working and the engine running only one way (to be able to run both) after about 20 seconds stops the motor, and can be started again after about 30 seconds. But only runds ca. 20 secounds
I bought 2 speed controller 2 engines and a programmeringsbox
Programmeringsbox not working and the engine running only one way (to be able to run both) after about 20 seconds stops the motor, and can be started again after about 30 seconds. But only runds ca. 20 secounds
i got the 200a esc and the big motor...great water flow...motor ran cool...esc went up in smoke in about 3 minutes....now gotta deal with shipping it back and warranty crap....if you can afford it...get something else
i got the 200a esc and the big motor...great water flow...motor ran cool...esc went up in smoke in about 3 minutes....now gotta deal with shipping it back and warranty crap....if you can afford it...get something else
How do i find out if iv been sent the new program card and usb cable? iv had the 200amp esc for months 10/3/13 and only just got a motor, so iv tested it today 11/12/13 and the motor ran for three seconds. i also have a 180 and 120amp aquastar, they work very well and get my home made wooden riggers doing over 140kph and 110kph for more than 5 minutes.
How do i find out if iv been sent the new program card and usb cable? iv had the 200amp esc for months 10/3/13 and only just got a motor, so iv tested it today 11/12/13 and the motor ran for three seconds. i also have a 180 and 120amp aquastar, they work very well and get my home made wooden riggers doing over 140kph and 110kph for more than 5 minutes.
| Update Instructions | Download [216] |
| 547753064X365809X55.pdf | Download [216] |
Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!
Others Also Bought
-
Turnigy AquaStar T20 3T 730KV/1280KV Water...SKU: 9052000029
$105.09 -
YEP 20A HV (2~12S) SBEC w/Selectable Volta...SKU: 9355000029-0
$15.65 -
Turnigy High Quality 8AWG Silicone Wire 1m...SKU: 171000711-0
$3.61 -
Turnigy High Quality 8AWG Silicone Wire 1m...SKU: 171000710-0
$3.61 -
Turnigy AquaStar 4084-1050KV Water Cooled ...SKU: 9192000091
$76.35