New Items Forum
Register

Total Price

$0.00

Cart 0 Cart 0 Loading...

Turnigy B12-30 4100kv Inrunner

Turnigy B12-30 4100kv Inrunner

Discontinued Product

Please continue searching for a similar product.
SKU:
TR-B1230-4100
WANT FREE SHIPPING? Click here to find out more!

Also known as a 130S class motor. The TR-1230 is an excellent motor for small EDF or Direct Drive appications. Think mini park jet type or small EDF for GWS planes.

 

Spec.
Kv: 4100rpm/V
Power: 32W
Turns: 17
Resistance: 732mh
Idle current: .2A
ESC Required: 10A
Lipo configuration: 2-4Cell (7.4 to 14.8v)

Dimensions:
Diameter: 12mm
Can Length: 30mm
Shaft length: 10mm
Shaft Width: 1.5mm
Front Mount distants: 8.5mm
Front Mount Thread: M2
Weight: 18g

  • SKU TR-B1230-4100
  • Brand Turnigy
  • Shipping Weight 39.0000
  • Packaging Length 0.00
  • Packaging Width 0.00
  • Packaging Height 0.00
  • Kv(rpm/v) 4100.00
  • Max Current (A) 0.00
  • Resistance (mh) 732.00
  • Max Voltage(V) 15.00
  • Power (W) 32.00
  • Shaft A(mm) 1.00
  • Length B (mm) 31.00
  • Diameter C(mm) 12.00
  • Can Length D(mm) 30.00
  • Total Length E(mm) 41.00
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

Don't know why but the shaft broke right where it was machined down. Did not have much time on this motor and did not get $8 dollars worth out of it either. Not sure if the blade was out of balance. I switched to a Blue Arrow BL1230 for now. Maybe I'll try the Turnigy B12-30 3850kv later.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Don't know why but the shaft broke right where it was machined down. Did not have much time on this motor and did not get $8 dollars worth out of it either. Not sure if the blade was out of balance. I switched to a Blue Arrow BL1230 for now. Maybe I'll try the Turnigy B12-30 3850kv later.

Got this motor even after reading all the reviews.

hooked it up on the bench to test before installing in my Gravity/Cox spitfire. Put oil in the bearings put on GWS 3x2 prop an used 2S 500ma lipo for the first run. Started it up on bench an all seamed fine. Then the motor got loose and the prop bumped the bench. The motor shaft broke off flush with the case. Sure am glad I did not get it all installed before I found out how soft the shaft is. Verry disappointed with this motor. I cannot reccomond it. I have another Cox P47 warbird with a medusa research motor that has been crashed hard several times and never had a problem with it flys great vwery fast. Spend a little more for the better quality.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Got this motor even after reading all the reviews.

hooked it up on the bench to test before installing in my Gravity/Cox spitfire. Put oil in the bearings put on GWS 3x2 prop an used 2S 500ma lipo for the first run. Started it up on bench an all seamed fine. Then the motor got loose and the prop bumped the bench. The motor shaft broke off flush with the case. Sure am glad I did not get it all installed before I found out how soft the shaft is. Verry disappointed with this motor. I cannot reccomond it. I have another Cox P47 warbird with a medusa research motor that has been crashed hard several times and never had a problem with it flys great vwery fast. Spend a little more for the better quality.

Great little motor - using this on a Eagle 50 (aka Walkera 22e) direct drive tail with a Esky Tail Blade Set 002386. The tail balde is the same as the BLADE EFLH1321, GWS 3x2 prop and also the HCB-03 from HobbyKing. I got a BLADE EFLH1321 mount and flipped it 180 so the the air flow is across the motor and with the addition of a heat sink the motor runs much cooler. I paired it with a Tz12A HobbyKing 12A BlueSeries brushless controller plugged into Assan GA-250 gyro and a walkera RX-2609 receiver that had the gyro mod (gyro board removed and gyro-sense jumper to AUX2).

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Great little motor - using this on a Eagle 50 (aka Walkera 22e) direct drive tail with a Esky Tail Blade Set 002386. The tail balde is the same as the BLADE EFLH1321, GWS 3x2 prop and also the HCB-03 from HobbyKing. I got a BLADE EFLH1321 mount and flipped it 180 so the the air flow is across the motor and with the addition of a heat sink the motor runs much cooler. I paired it with a Tz12A HobbyKing 12A BlueSeries brushless controller plugged into Assan GA-250 gyro and a walkera RX-2609 receiver that had the gyro mod (gyro board removed and gyro-sense jumper to AUX2).

I bought this for a losi 1/24 rally. It works great. good speed and power and barely gets warm with 3 cell lipo with 17t pinion and 53t spur. awesome! I would definitely recommend!!

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I bought this for a losi 1/24 rally. It works great. good speed and power and barely gets warm with 3 cell lipo with 17t pinion and 53t spur. awesome! I would definitely recommend!!

Great brushless. Used in losi 1/24 4wd rally. Wish it came with connecters soldered. Also used turnigy 18A esc w

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Great brushless. Used in losi 1/24 4wd rally. Wish it came with connecters soldered. Also used turnigy 18A esc w

YA HICE UNA PUBLICACION POSITIVA, PERO COMO DATO ADICIONAL, EL
A 10 QUE VA MONTADO CON FAN DE 50MM LO ESTOY VOLANDO CON
4S, RHINNO 1000MAH ,30C.
LOS ATAQUES EN PICADO QUEDAN MUY LINDOS.
SALUDOS DESDE URUGUAY................FLAVIO

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

YA HICE UNA PUBLICACION POSITIVA, PERO COMO DATO ADICIONAL, EL
A 10 QUE VA MONTADO CON FAN DE 50MM LO ESTOY VOLANDO CON
4S, RHINNO 1000MAH ,30C.
LOS ATAQUES EN PICADO QUEDAN MUY LINDOS.
SALUDOS DESDE URUGUAY................FLAVIO

Not what I expected. Bearings are not good.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Not what I expected. Bearings are not good.

buen motor, esta montado en un gws a 10 con fan de 50mm. y lo lleva de maravilla.

saludos desde ururguay..........flavio

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

buen motor, esta montado en un gws a 10 con fan de 50mm. y lo lleva de maravilla.

saludos desde ururguay..........flavio

Runs little bit hot on 3S with GWS 60x25 prop, mpst like too high kv for this setup, need to order less kv motor as i like these.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Runs little bit hot on 3S with GWS 60x25 prop, mpst like too high kv for this setup, need to order less kv motor as i like these.

great little inrunner. perfect for the gws 40mm ducted fan. I strongly recomend getting a heat sink.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

great little inrunner. perfect for the gws 40mm ducted fan. I strongly recomend getting a heat sink.

  1. 1
  2. 2
  3. 3
  4. 4
Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!