Register

Product Finder

Settings

Useful links

Live Chat
 
[["US","AU","GB","DE"]]
Register

TURNIGY Bell TR2410-8 890kv Outrunner

TURNIGY Bell TR2410-8 890kv Outrunner

Discontinued Product

Please continue searching for a similar product.
Rating:
Stock:
OUT OF STOCK
Weight:
87 g
SKU:
TR2410-8
Product
Description

The TURNIGY bell motor looks and runs exactly the same as the Towerpros, at 2/3 the cost!

Turnigy Bell TR2410-8 890kv
Dimensions: 31 x 62mm
Weight: 58g
Power (W): 109
Turns: 8
Resistance: 269moh
Idle Current: .6A
Esc Required: 20A
Lipoly: 2-3S
Prop: 8x6 e-prop

Product
Specifications

Additional Information

  • SKU:
    TR2410-8
  • Brand:
    N/A
  • Shipping Weight(g)
    87.00
  • Length
    0.00
  • Width:
    0.00
  • Height:
    0.00
  • Kv(rpm/v)
    890.00
  • Unit Weight (g)
    58
  • Max Currents (A):
    0.00
  • Resistance (mh):
    269.00
  • Max Voltage(V)
    11.00
  • Power (W)
    109.00
  • Shaft A(mm):
    5.00
  • Length B (mm):
    35.00
  • Diameter C(mm)
    25.00
  • Can Length D(mm)
    16.00
  • Total Length E(mm):
    62.00
Community
Discussions
Rate&
Review

Write Your Own Review

Only registered users can write reviews. Please, sign in or sign up

verified_user Quality
trending_up Value
playlist_add_check Overall
Excelente, el envio fue en solo 15 dias.. el motor funciona de maravilla, le tengo puesto una bateria de 11 V y un esc de 20A en un velero..
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
nice motors...recommended 8*6 prop was out of stock ,so using 7*3.5 :( - mount is a little small compared to cf-2812 motor..
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Very poor. Has a brass bushing instead of a bearing on the latest one I got. The little clip seats outside of the bushing and thus creates a lot of drag in the motor as well.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
timo paneli, esses motores da Turnig sao os melhores.

Eu sou f deles.

Recomendo.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
It's quiet fit in building quad/Qocto copter and using 2200 lipo battery. The quad/Qocto have the ideal weight then can fly about 7 - 10 minutes
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
It's quiet fit in building quad/Qocto copter and using 2200 lipo battery. The quad/Qocto have the ideal weight then can fly about 7 - 10 minutes
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I purchased this motor for quad rotor. The small KV of this motor make the quad rotor can fly smoothly about 7 minutes.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I purchased this motor along with the SuperSimple 20A speed control to replace a brushed direct drive 480 motor in a 20 oz Decathlon foamie. With the direct drive setup the brushed 480 barely had enough torque to stay in the air. Converting to the Turnigy BELL TR2410-8 and LiPo batteries saved over 2 oz and the plane can now clime out at 45 degrees.



The only issue I have had with this motor is keeping the set-screws tight. They should not have been spaced 180 degrees apart. I changed the set-screw spacing to 90 degrees and have not had another issue.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Performance wise, this motor is very close to the GWS EPS-350C-DS. It has the EPS-350C-DS' weight and about the same thrust per given battery and propeller. It's a tad bit more efficient and can be pushed a little harder but it's still basically a 1.1-for-1 GWS power system replacement. Your Slow Stick with this motor will fly much like it had the stock motor.



The motor's base is a bit too small for the supplied [GWS] plastic stick mount so I epoxied a plywood circle into the mount for a screw base. The prop shaft only has 1/2 bolt threads so just push your GWS prop all the way down to the base then bolt tight from the outer end. The motor itself differs from most CDROM's in that its wound with 4 strands of thin angel hair in a Wye configuration (as opposed to Delta) giving the motor a lower KV, higher torque, and quieter whine free running. The quality itself is fair, mixed. The 14 magnets are a tad small, the gaps a little wide and uneven, and the windings are on the sloppy side but such marginally affects the motor's performance. The bearings were tight and there was no noticeable balance or bell wobbles issues although the standard firewall mount only has 2 grub screws when 3-4 would work better if your Xmas tree stand only had 2 opposing bolts, you would just lean your tree against the wall. I've had many good flights with this motor and I like its potential to be rewound LRK/DLRK (14m - 12p).



It's an interesting, rugged, inexpensive, and serviceable motor. I give
verified_user Quality
trending_up Value
playlist_add_check Overall
Upload
Videos
Upload video
Upload
Files

Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.