This is the version 2 of the tiny yet brilliantly designed Micro-Quad, features a stronger integrated PCB frame and motor mount design but retains the same simplistic idea of bolting on the motors, then solder your choice of ESC directly to the frame!
An integrated power distribution system is also included making for one of the neatest electronics and lightest installs around. All mounting hardware and frame components are included in the kit. All you will require to have this little micro sized in the air is four micro motors, four 6-12Amp ESCs, a set of 5x3 Micro-quad props (2 Clock wise and 2 counter clockwise) an 800mah 2s or 3s Li-poly battery, a HobbyKing Multi-rotor control board and your own transmitter and receiver (TX/Rx).
• Light weight design.
• Integrated PCB for component installation.
• Included a full set of frame and mounting hardware.
Flying Weight: 145g (not including RX and battery)
Width: 250mm~220mm hub to hub
4 x Multistar DT1704 or Turnigy T1811-2900kv
4 x 6-12Amp ESC
4 x 5x3 Prop (2CW & 2CCW)
1 x HobbyKing Multi-Rotor Control Board or any FC with 45 x 45 mm mounting
1 x 800Mah 2s or 3s Lipoly battery
16 x M2x8 Bolts (for motor)
16 x M2 lock nuts (for motor)
Your own transmitter and 4 channel receiver.
petite drone tres facile a monter, dommage, pas difficile pour le monter, mais faut pas de grande main.Sehr sauber gearbeite Teile, auch f?r einen Anf?nger sehr einfach zu l?ten.
Alle Bauteile vorhanden und passgenau.
Put 2 of these frames together for a mini x8 DYS 1306 2300, MS V2 6AMP ESC, naze32 full, 6mm black nylon spacers. super strong. My favorite multirotor to flyI never had luck with this frame. The arms flex a lot. Also there isn't a great amount of room for everything. I scrapped this frame and most of it is now in the garbage can.Perfect setup for a micro quad with easy to set up kit. In just less than an hour the complete electronics was set up and ready to fly with this kit. very light and and robust kit. perfectly laser cut just locks in place all parts.I bought this to replace my V.1 Micro Quad after I had one-too-many hard landings.
It's such an improvement over the original as it allows for through-hole soldering which makes it really easy to install or replace the electronics. There are plenty of additional power take-offs to allow you to add LED's without having to run wires from all over the frame. Also it looks MUCH cooler in black!I never flew with this frame, but is seem to be a good little frame. Weight: 66gI bought this frame as a spare for the white ARTF. Glad i did as i smashed it up! This black frame however seem slightly stronger and holds up better to slight dings. dozens of flights later and it's still working and not been glued! Would buy again for sure!Als Ersatz bestellt da er doch leicht kaputt gehtThis is my first micro quad and I love it. The frame is very well done and I love the black color!
4x HK 1811 2000kv (silver motor)
4x HK 10A ESC (simonked)
HK MultiWii AIOP controller
HK Neo 6 GPS
1000mAh 3s 20C battery
It is one small beast! I will upload a video when I have some free time to shoot it.
HasseÂ´s Micro Quad with landing gear download now [305kb] Mini X8 download now [3866kb] Mini X8 download now [3866kb] No File Name download now [3135kb] Micro-Quad V2 Fpv download now [2672kb]