The Turnigy Marine waterproof speed controllers are packed with the latest technology and are up there amongst some of the best on the market today. These speed controllers have reached the ultimate IP67 level of protection (Ingress Protection), this is the standard that electronic devices are tested to. The 6 on the IP rating means it is "Totally protected against dust", the 7 on the IP rating means it is "Protected against immersion between 15cm and 1m.
The Turnigy Marine speed controllers are supplied with a "Copper Bar Heat Technology" water cooling system (exclusively patented) and extremely low internal resistance MOSFET's. Each one has specially designed software which features excellent start-up and acceleration performance, they have an outstanding amount of "punch" when coming out of turns when used in high speed boats. A waterproof on/off switch is fitted so that you can connect the battery then seal the hatch, the radio can then be switched on when you are ready to go.
2 running modes can be selected, either forwards only or forwards and reverse. The speed controllers also have multiple protections as shown in the features list below. Programming of the many features of the speed controller is easily done using your transmitter.
• Patented water cooling system
• Excellent start-up and acceleration performance
• Bags of "punch" when accelerating out of turns
• Fitted with waterproof on/off switch
• 2 running modes can be selected (forwards only or forwards and reverse)
• Programmable via the transmitter
• Program modes: running mode, LiPoly cell count, low voltage cut-off, timing
• Overheating protection
• Low voltage cut-off protection
• Signal loss protection
Voltage Input: 2~6 LiPoly cells (6~18 NiMh)
Continuous Current: 120A
Burst Current: 720A
BEC Type: Switching with on/off switch
BEC Output: 6V@5A
Motor Connectors: 4mm
Servo lead: JR style
Servo Lead length: 300mm
Water Cooling Pipe: 3mm I/D~5.4mm O/D
Please note: This speed controller is not supplied with a battery connector.
does the jobUsing in a proboat shockwave 26 with a 3660 1500kv motor with 38 mm prop on 6s. Esc runs cool and works great. Highly recommend.bon produit livraison rapidetesting this on my princess. running on 6s 30c 5400mah. incredible speed with leopard 4074 2110 kv.. after a few round i notice my boat speed is become half of speed. i cek the battery still have plenty of charge.. so i running it again but still the same.. i come home and check it again. i was notice my soldering was poor.. 1 of connector nearly snap off.. but i amaze with this esc.. so i think my connector cant hold amps at wire ..im using xt60.. so the esc detect that problem. esc temp rise more then 80degree. then it cut half of the power.. what a nice esc..... if not my esc definetly burn.. ty hobbyking... dont hessitate.. buy it.. (sorry for my broken english)regolatore di pessima qualit!avevo due 3s collegate in serie dopo aver accelerato al massimo la barca non funzionava pi...dopo tre secondi esploso l'esc...risultato:barca da buttare perch dalla pressione si aperta a meta...regolatore ovviamente da buttare anche quelloburned in my osprey in 10 minutesSo far, I'm very pleased with this ESC. I bought it to replace the defective ESC in my Surge Crusher catamaran, and it's worked perfectly. Throttle control is very smooth, and it's not even warm to the touch after running hard. I'm sure i'm not pushing it very hard with the stock motor, but it's good to know I have some headroom if I ever want to upgrade. It's also approximately the same size (footprint, at least) of the stock ESC, so it fits just fine. Hopefully it lasts a long time. As of now, It seems to be a good unit for a fair price.muy buen esc buenas terminaciones,lo uso con un motor 36/74 con prop de 42mm,bastante eficiente y muy buen precio para un esc de 120 amp.Great esc never over heats and gives a great punch to my boat when i need it