Become a Supplier Blog New Items
Register

Total Price

$0.00

Cart 0 Cart 0 Loading...

Turnigy Mobius 2-Axis Gimbal with Tarot Controller and AX2206 Motors

Generating Links

Turnigy Mobius 2-Axis Gimbal with Tarot Controller and AX2206 Motors

Price:

Now save save $78.43 $78.43

Special Price $28.42 $28.42

You save save $78.43 $78.43

Was  $106.85

Shipped From:
  • USA
  • Global
Already Purchased Discontinued Product

Please continue searching for a similar product.
SKU:
9171000509-0
want FREE shipping? Click here to find out more!

Turnigy have recognized the Mobius ActionCam as the go-to camera for the RC hobby and set out to make a low cost, light weight, quality component 2-Axis gimbal to match the Mobius’s smaller size.

The Turnigy Mobius gimbal started with the popular AX 2206 BLGM, perfect for its small size and being well known as a great motor. From there Turnigy had the motors custom made to match their spec. The Turnigy Mobius gimbal looked to one of the leaders in gimbals for their robust controller and easy GUI interface, settling on the Tarot 2 axis BGC as the heart of the Mobius gimbal and includes the USB programmer for future updates and configuration. Turnigy then set out to create a lightweight and robust frame around the Mobius and chosen hardware. The result is the one of best gimbals available and best of all it’s made specifically for the Mobius.  

Features:
• Light Weight
• AX2206 Gimbal motors
• Tarot BGC and IMU for control
• Stick and Rate mode for roll and pitch control
• RC roll and pitch control
• ALL CNC Aluminum and composite frame
• Included USB programming tool

* Note: Please pay close attention to the bolt locations in the instructions, and note the pitch motor uses the 2 M6 bolts, if the M8 bolts are used could damage the motor windings causing the pitch axis to shake when powered.

Frame specs:
Size: HxWxL 76x67x100mm max all around size
Weight: 160g

Motor Specs AX2206:
Poles: 12N14P
KV(RPM/V): 140
Resistance: 11.25omh
Weight: 32.3g
Wire: 0.17mm
Torque: 230g
Bottom holes center to center: 16mm and 19mm
Top holes center to center: 12mm 

Tarot ZTX22 Specs:
Working Voltage: DC 7.4V ~ 14.8V (Recommended 12V, three lithium battery)
Working current: 200mA-500mA (power supply voltage and the motor related)
Working temperature: -15c ~ 65c
Processor: Dual 32-bit high-speed ARM core processor
Sensor: Three rotor MEMS gyroscope rotor MEMS accelerometers
Maximum angular rate: 2000 ° / sec
Maximum acceleration: 16g
Control frequency: 2000Hz
Motor drive frequency: 20KHz (no noise smoothing drive)
Control accuracy: 0.1 degControl angle range: -45 ° ~ 45 ° (roll), -135 ° ~ 90 ° (tilt)
Power Interface: DC 7.4V ~ 14.8V (Recommended 12V, three lithium battery)

Note: This is a Kit and does require some assembly and a Windows based computer to flash the Tarot configuration with the included USB tool.

  • Turnigy Mobius 2 Axis Gimbal
  • <" style="background-image: url(https://img.youtube.com/vi/JjLCdvFrprk" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen>
    Turnigy Mobious 2 Axis Gimbal
Upload video

Only registered users can upload video. Please, log in or register

Topics
Sort by
Most Recent Topics
* Nickname:

* Your Reply:


Please, enter the text shown in the image into the field below
*Verification Code:
Cancel
Submit
Post a new Topic
* Nickname:

* Your Topic:



Please, enter the text shown in the image into the field below
*Verification Code:
Post Topic

Only registered users can write reviews. Please, sign in or sign up

randy | Verified Buyer

  • Overall
  • Quality
  • Value

Nice size. Made well.

Aug 26, 2019

Looks decent . I hope the board functions properly for its unused so far.

Maximilien | Verified Buyer

  • Overall
  • Quality
  • Value

RAGE

Oct 13, 2018

une fois brancher sur l'ordi, mes problème en commencé. Entre l'ordi qui na pas les bon driveur un coups sur deux et le logiciel qui crash des qu'il détecte la gimball. J'en peut plus..

Lundy_ | Verified Buyer

  • Overall
  • Quality
  • Value

You need a bit of patience to get it working .

Mar 22, 2018

The assembly is straight forward and easy to do .But the problems started when I connected for the first time the battery, I was faced with a untamed wild jumping bronco gimbal ,that was in no way useful to take any video. Even after connecting to the configuring program I was not able to tame it.One motor was burnt through caused by the uncontrolled up and down jiggling of the gimbal, I have ordered a spare motor and could solve that part of the problem.
The program was saying the latest version software 1.5 was installed ,and all my attempts to tweak it via the configuration software failed.After hours of trying and fiddling on the settings I decided to reinstall the firmware 1.5 again ,and that solved the unmanageable gimbal in to a workable solution, I needed a long time to fine tune it but in the end its working smooth and without jiggle problems .So I think that the installed firmware was somehow damaged in some way. and now everything is working like it should do.
The construction of the gimbal is not very Mobius friendly ,the way it is to connect to the gimbal platform is a paste and cut work solution with double sided sticky tape and a rubber band ,while the camera comes with a perfect holder with camera thread, with a little creativity you can drill a hole yourself in the platform and still leave room for the gyroscope and accelerometers that are situated under the camera platform .
After this ,shall we say little set back ,I have now a nice working gimbal for little money.
Don't give up to eazy on it ,you can make it work ,it only needs a lot of your time and patience .

David | Verified Buyer

  • Overall
  • Quality
  • Value

Customer Rated

Sep 14, 2016

I have adapted the Turnigy gimbal to use the RunCam2 camera. I made an aluminium holder attaching it with four small countersunk head bolts and nuts with lock washers. Under the holder is some thin sheet lead so that when there is no power the camera is completely balanced. A couple of rubber bands hold it in case of hard landings. My videos are now very smooth and great to view.

lampo.ep | Verified Buyer

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Sep 07, 2016

precio bueno y calidad tambien

Engy66 | Verified Buyer

  • Overall
  • Quality
  • Value

Customer Rated

Aug 08, 2016

Every time that I connect the gimbal the motors do not start and the light sets at Green solid in mode Over current. Can anyone help me?

Beachcomber | Verified Buyer

  • Overall
  • Quality
  • Value

Customer Rated

Jul 19, 2016

Just finished installing this gimbal on my quad, for use with RunCam HD (similar in size to Mobius). Can't complain like the other reviews. Mine just works. No melting plastic, no blue smoke. Here's a couple of tips. Go to the same item at International Warehouse, and click on "videos" and "files". You'll get lots of good info. I downloaded the latest version 1.5 software before receiving my gimbal. but discovered it came with ver 1.5 in both gimbal and motor control, so I didn't need to re-flash. Will admit adjusting all the parameters was (and still is) a pain. Default settings are not for RunCam / Mobius. A couple of files suggest different settings, but I had to fiddle even with those to stop the jiggle. Still trying to fine tune, but getting pretty stable on my wobbly quad.

pardus | Verified Buyer

  • Overall
  • Quality
  • Value

Customer Rated

Jul 05, 2016

Didn't have luck with this. Tuning is very difficult and I could never get smooth video no matter what I tried and I tried a lot over 3 months. The motors are also way overkill for a Mobius and the whole gimbal is very heavy to carry a light Mobius. Not worth the price.

Earl | Verified Buyer

  • Overall
  • Quality
  • Value

Customer Rated

Jun 26, 2016

Purchase this a few weeks back and it's still not working. I'm sure its me, but getting this setup is a pain. Haven't spent a lot of time on it, but why isn't this sent already flashed so you don't have to do the find, flash and configure thing. I'd rather be flying.

| Verified Buyer

  • Overall
  • Quality
  • Value

Certified Buyer Rated

May 22, 2016

????? ?? ????? ??????, ?????????? ????? ??????! ???? ???????? ? ???????. ?????????? ? ?????? ???????. ???????? ??????, ????? ????????? ?????????????.

  1. 1
  2. 2
  3. 3
  4. 4
  5. 5
  6. 6
Customer files
PRM0175.pdf Download [1716]
No File Name Download [21]
Revised Plate Download [95]
Tarot 2-Axis Brushless Gimbal for Gopro Download [594]
BadgerJed setup lessons learnt - Turnigy Download [319]
No File Name Download [2126]
insttruction's and link to software.doc Download [26]
Software & Config 2018.docx Download [12]
Software & Config 2018 Download [12]
mobius conf 1 Download [12]
Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!