Country
United States
 
Shipped From:
  • UK
  • United States (US)
  • Global
  • Australia (AUS)

Turnigy TY-P1 25Amp HEXFET Brushless Speed Controller

Turnigy TY-P1 25Amp HEXFET Brush...

The Turnigy TY-P1 25Amp ESC is a stand out performer. Using quality IR HEXFET® Power MOSFETs developed in the USA, this ESC is cable of handling current draw in excess of 40 amps. However this in house designed ESC was developed and produced b...
TYP1-25A

Now save save $2.50 $2.50

Special Price $9.99 $9.99

Now save save $2.50 $2.50

Was  $12.49

70g
TYP1-25A


Max Qty add to cart is -1 in one time

Suggestion Box

Please let us know if you found any issues with this product listing.
We take our customer comments very seriously and in many cases our website modifications and product updates are a result of your comments!

Price War

If you've seen a product elsewhere for a better price, please let us know! HobbyKing pride themselves on offering the best price, so if there if you see something cheaper elsewhere, let us know!

Overview

The Turnigy TY-P1 25Amp ESC is a stand out performer. Using quality IR HEXFET® Power MOSFETs developed in the USA, this ESC is cable of handling current draw in excess of 40 amps. However this in house designed ESC was developed and produced by the HobbyKing engineering team with one goal in mind, quality and reliability. Rather than over rate the ESC and push it to the limit with a larger heat-sink, as many companies do, we wanted to design a Speed controller for those looking for a bullet proof solution. We use SMT technology rather than hand soldering to produce consistent  quality and reliability each and every time. The TY-P1 25A ESC also features independent voltage regulators (One for the BEC and one for the MCU) this ensures the MCU will remain powered in the event of a high momentary amp draw from the BEC circuit and vise versa. An XT-60 battery connector and 3.5mm bullet connectors have been pre-soldered for convenience.

Specs:
Cont. Current: 25A
Burst Current: 50A
BEC: 5volts / 2amps
Weight: 42.5 Gram (including wires and plugs)
Battery Plug: XT-60
Motor Plug: 3.5mm Bullet Connector

Programming Options:
Brake (OFF/ON).
Cut-off Type (Soft-cut/Cut-off).
Cut-off Voltage (Low / Middle / High ).
Start Mode (Normal / Soft / Very Soft ).
Timing Mode (Low / Middle / High).
Cell (Auto, 2S, 3s, 4S).

Note: Programming can be done via the Optional programming card. See related items below.

This ESC requires the user to set the throttle range on installation. Please download the manual for further instructions.

HEXFET® is a registered trade mark of International Rectifier Group California, USA.

Specs

Additional Information

  • Blade Count:
    N/A
  • Diameter X(Inch):
    No
  • SKU
    TYP1-25A
  • Watt Hour
    0.00
  • Weight(g):
    70.00
  • Length:
    120.00
  • Width
    10.00
  • Height
    100.00
Discussion
Reviews

Write Your Own Review

Only registered users can write reviews. Please, log in or register

love these ESC great for bigger planes like the Flite Test Guinea Pig
come da descrizione all'atto dellla vendita, molto soddisfatto
Very good esc , easy card programming for multirotor
This is very good for my Quad
Great works perfectly with my ft Guinea pig and just like vid says this wax is meant to be 40 amp
Tought it was broken, but is didn't calibrate it... normally you don't have to wait so long to calibrate it but its ok. Actually these are pretty nice
I actually have 17 of these in various multirotor aircraft that have worked perfectly for years now. They are reflashed with SimonK firmware. These were bought some time ago. I bought one recently that did burn out when setting up a FPV plane, I think it was a bad solder joint either on the esc or on one of the extensions I was using because the motor kicked back and forth when trying to power up and that's a sure sign of a bad connection.
The moment I plugged this in it blew up.
I can't recommend this product to anyone. Please avoid this product.

I had some test flights (5mins?) with my new quadcopter and these ESCs yesterday. After some KK2.1 parameter tuning today, I went to field to test new configuration. Right after plugging in the battery (Turnigy 2200mAh, 3S), I noticed some propeller movement, spark sounds from the esc AND SMOKE FROM THE ESC! Esc warmed a bit and is for sure broken.

Please note: the esc burned right after plugging in the battery. No throttle, no overload.

Now I am considering whether I should replace all my ESCs because if one burns like this, others may also. Next one might burn the flight controller and/or motors, if this one already didn't...
Bought 4 of these since they were suggested by HK for my quad project. I would not suggest getting these to use with the Multiwii board. After many, many hours of work 1 works all the time, 1 works sometimes, and 2 just beep. They all work fine connected directly to a Spektrum receiver. I don't think they communicate well with the multiwii.
View all reviews
Video
  • Turnigy TY-P1 25Amp HEXFET Brushless Speed Controller

Upload video
File

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.