Country
United States
 
Shipped From:
  • US (West)
  • Global
  • AU
  • EU

Turnigy™ TGY-5513MD DS/MG Servo 12kg / 0.18sec / 54.5g

Turnigy™ TGY-5513MD DS/MG Servo ...

The Turnigy TGY series offers excellent performance and quality at a great price. The TGY-5521MD digital servo offers precise centering and an ultra-durable metal gear drivetrain.

Model: TGY-5513MD
Dead band: 2us
Working frequ...
9295000005

Now save save $0.00 $0

$10.10
125g
9295000005


Max Qty add to cart is -1 in one time

Suggestion Box

Please let us know if you found any issues with this product listing.
We take our customer comments very seriously and in many cases our website modifications and product updates are a result of your comments!

Price War

If you've seen a product elsewhere for a better price, please let us know! HobbyKing pride themselves on offering the best price, so if there if you see something cheaper elsewhere, let us know!

Overview

The Turnigy TGY series offers excellent performance and quality at a great price. The TGY-5521MD digital servo offers precise centering and an ultra-durable metal gear drivetrain.

Model: TGY-5513MD
Dead band: 2us
Working frequency: 1520us / 330Hz
Operating voltage: 4.8~6.0V
Operating speed (4.8V): 0.20sec/60°
Operating speed (6.0V): 0.18sec/60°
Stall torque (4.8V): 11.89kg.cm (165.15 oz/in)
Stall torque (6.0V): 12.25kg.cm (170.15 oz/in)
Connector wire length: 265mm
Dimensions: 40.5x20.2x44.2mm
Weight: 54.5g

Specs

Additional Information

  • Blade Count:
    N/A
  • Diameter X(Inch):
    No
  • SKU
    9295000005
  • Weight(g)
    125.00
  • Length:
    85.00
  • Width:
    40.00
  • Height
    65.00
  • Speed (Sec/60deg)
    0.18
  • Torque(kg)(min. 0.01kg):
    12.25
  • Unit Weight (g):
    N/A
  • A(mm)
    44.00
  • B(mm)
    41.00
  • C(mm):
    41.00
  • D(mm):
    20.00
  • E(mm)
    54.00
  • F(mm)
    27.00
Discussion
Reviews

Write Your Own Review

Only registered users can write reviews. Please, log in or register

Wie gewohnt toll nur sehr hoch, im Std. Size Bereich gibt es fast den gleichen Servo nur 1cm niedriger,,..

L?uft bisher gut...

Use these servos everywhere, 1.5A amps when blocked, remembers this when bying power distributor.

Very happy with them. Use on a Edge 2m
Servos have a lot of overshoot and poor centering. Gears have a lot of play. I was going to use them in a 1/4 scale edge but changed my mind.
Stay away from this servo if you want one that lives for more than a few hours.
Mechanical build quality is fine, the electronics / software, however, isn't. The regulation lacks an Integral part in its PID regulation. Even without load on a servo tester, it did not always reach the set point, most of the time it just just stayed close to the desired position and kept humming, as the pulses the control circiut gave to the motor when it was close to the set point were too short to make it move to the desired position. An integral term in the PID controll should address just that.
You can imagine what happens, when it has to drive some load (and yes, it is strong): It permanently drives the motor and never really reaches the setpoint. Hence, the life time is short, mine died after only a few hours of operation. The motor is shortcut now, even though the crappy driving circuit is still fine (was used on a current limited 5V supply).
It could be as simple as adjusting the PID parameters, however this digital servo cannot be programed.
Guter Servo. Passgenau, stark und gnstig
Attention Attention!!! Please do youre self a favour and put a little isolation strip under the servomotor leads because they can create a short circuit which destroy youre servo and probably also youre model. Message to Turnigy: please modify. This modification will support safety.
Attention Attention!!! Please do youre self a favour and put a little isolation strip under the servomotor leads because they can create a short circuit which destroy youre servo and probably also youre model. Message to Turnigy: please modify. This modification will support safety.
Update........There is no brass bushings in the lid to hold the gear pins in place, Its just pressed Into the plastic case(no support) In any sort of crash/bump, This centre pin falls out of place then the gears are out of alignment. Servo lock's up and it's buggered... They really should have put a metal bushing in to hold it better like most servo's have(not this one)

This pin slot is the weak spot in this servo, Due to this, I have found this servo not good for monster truck bashing, Because any bad landing or hard bump on the steering will ruin the servo(very weak pin slot in casing), I have used 2 of these servo's, And both were broken due to this within 2 week's.
Gears seem reasonably strong, But this does not matter as the next weak spot is the centre pin slot, Once this slot is worn, Servo is useless.
Would be best suited to some application where there will be no impact on servo, I can only assume that all this line of Turnigy servo's are the same(no bushing) so I think ill steer clear from these form now on.
4/10
It's very good product !! Very strong ! I use this on one 1/8 buggy and it's perfect ! It's compatible with lipo 2S and there is all metal gear !!
Thank you very much hobbyking !!
This is a full size standard servo. It is slow compared to some micro servos, but it is fast compared to other standard servos. I am using it for robotics. It has a full 180 degree response when pulsed. It is quiet, smooth, and powerful. I will be using this servo for other projects from now on.
View all reviews
Video
Upload video
File

Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.