Register

Product Finder

Settings

Useful links

Live Chat
 
[["US","AU","GB","DE"]]
Register

Vision EP Balsa 3D 940mm (ARF)

Vision EP Balsa 3D 940mm (ARF)

Discontinued Product

Please continue searching for a similar product.
Rating:
Stock:
OUT OF STOCK
Weight:
1326 g
SKU:
VisionWP-A053
Product
Description

Retro style EP 3D Fun Flyer, Balsa construction. This plane suits stick mount motors as well as firewall mounted motors.

Spec. 
Wing Span: 940mm
Fuse Length: 910mm
Wing area: 17.3cm sq.dm
Flying Weight: 450g ~ 540g

Includes:
All Hardware
Decal Sheet
Instructions

Requires:
Your Own 4 Channel TX/RX
4 x 9g Servo
BL22 Motor or Brushless Gearbox
20A ESC
1000mAh~1300mAh 3s Lipoly Battery

Product
Specifications

Additional Information

  • SKU:
    VisionWP-A053
  • Brand:
    N/A
  • Weight(g)
    1326.00
  • Length
    770.00
  • Width:
    120.00
  • Height:
    260.00
Community
Discussions
Rate&
Review

Write Your Own Review

Only registered users can write reviews. Please, sign in or sign up

verified_user Quality
trending_up Value
playlist_add_check Overall
tried ... yesterday, my first impression, I would say great, ok balance, stability, ok, ok inverted flight, I think that this aircraft can be a basis to begin the aerobatics, however, in any case, the advice is for fun and is for the flight to figures ... very nice
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I'm flying my Vision EP with a Turnigy 2209, 28 turn, 1050Kv Brushless outrunner motor, using a 3S 2200mah Nano-Tech Li-Po on a 10" x 4.7" APC prop giving 900g thrust at 18.4 Amps and at 11 Watts. It works really great with this model keeping it very light. Plenty of poke in this motor and it doesn't get very warm at all (neither does the 20 Amp ESC). Very free running, doesn't give much breaking effect as the prop windmills power off, even a very low airspeed. Great little motor for lighter aerobatic models.
Model flies great and is impressive when doing aero's at low speed close in. Model is for those who want a bit of finesse in their flying rather than "Throttle Jockeys" and high speed flying. Think those who report breakages of tailplanes are using too much power and speed and are probably using heavy motors/batteries etc. KEEP IT LIGHT and it's a very rewarding buy.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Very well built and finished, the covering being particularly good. Good instructions etc. Very well boxed and arrived with no damage whatsoever. All parts there nothing missing. Mounting holes for servos are perfect and needed no cutting to allow fitting of servos. The only fly in the ointment is the recommendation by Hobby-King on their Global Website of the suitable motor for this model i.e. EPS100 brushless motor with gearbox which has to be stick-mounted. Pictures of this model show the two forward bulkheads cut to take a stick-mount. The model has now been modified and supplied with different bulkheads and no provision for stick-mounting. There is now a box type motor mount supplied which takes a 2209/28 1050Kv brushless motor, on which it flies very well.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
This plane is a very good deal. The plane is build very clean and I fly it with a smal engine. It was so good, that I bought a second plane one week later.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Maidened this one today in about 10-12 mph wind.
My setup: KD A22-20 spinning an 11x4.7SF, 30A ESC, 1300 mAh 3S and 4x HXT900 servos.

Well behaved and handled the wind very well. Elevator & rudder seems a bit small for full out 3D, but I'll maximize the throws and give it a try when there is a bit less wind :)

verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
This is an outstanding plane. It's a mid-wing tail dragger, so it's not a trainer. But the quality of the finish, the straightness of the build, and the ease of completion make this one of the best I have seen. It is built up of balsa and (minimal) hardwood. The optional motor mount and much of the fuselage is lite ply. On the down side, the main landing gear is quite flimsy, and the wheels provided are small, so the first modification I made was larger wheels to allow use from our grass field.

If you decide to put in a stick-mounted motor, you will need to provide the stick. There is a booklet with very limited instructions on assembly, but it has good pictures, and it covers all of the basics. The finished plane is a very nice-looking model you can be proud to take to the field.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
A rather older design, but the plane flys well. Remember to reinforce the horizontal stab to prevent stab failure during flight. I use Hobby Kings 1mm flat carbon fiber
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I have received the kit today in Belgium.
It's a very beautiful aircraft, very light and the covering is superb.
It's a very good deal for the price and I now I will buy the blue model again.

verified_user Quality
trending_up Value
playlist_add_check Overall
Upload
Videos
Upload video
Upload
Files

Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.