The Dual Reciever Unit is a wireless buddy box interface that can be used in a variety of ways and even allows 2 different makes of Transmitter to be used in a Buddy configuration!
This has amazing advantages over the traditional system that has always required the master and slave transmitter to be the same make and on top of that, you have to be connected to each other via an easy to pop out short cable and in turn, the cable ends have to match......the Dual Reciever Controller does away with all of that.
The Unit inter-connects 2 x 4 channel Recievers that do not have to be the same make and this in turn allows JR Servo configuration to work with Futaba servo configuration and so on. As well as pilot training, this unit can allow 2 x TX to control one model, this has many potential applications, for instance, for safe FPV flying, this will allow your observer to take over the flight at the flick of a switch if need be. The unit is small and light as well as simple and fast to set up and isnt much more expensive than many buddy leads!
Klein, leicht und günstig. Kann in Kaskade verwendet werden, um die Anzahl der Kanäle zu erhöhen.Pequeno, ligero y barato. Se puede utilizar en cascada para aumentar el numero de canales.Small, light and cheap. Can be used in cascade to increase the number of channels.Petit, leger et pas cher. Peut être utilisé en cascade pour augmenter le nombre de voies.Excellent module dcolage.
Possibilit de jumeler deux modules pour avoir plus de 4 voies.
Trs facile brancher et utiliser, aucune latence au passage d'instructions entre les deux radios.
Juste s'assurer qu'il y ai assez de place dans le fuselage pour l'installation.
Penser aux cordons (mle/mle) supplmentaires pour les branchement.
Voir mon fichier (Want more than 4 channels ?) dans le dossier Filesworks awesome!
to everybody that wants to install this in your plane and struggle to get your esc to work.
make sure sub-trims on your throttle on both remotes are set to below minus.
i had a hard time trying to get mine to work and didn't realize my trims was on zero.
for some or other reason on startup my esc got throttle signal even when my trims was on zero.
Fantastic 5-star product, I use it all the time. Nice shiny finish, good to hold in my hand. You can be sure i'll buy more soon.works great! well worth my money, no point getting the 8ch for me as i only use it for multirotors. FS is the switch to your aux channel (if still in doubt can look at the files section, someone posted a diagram) all i can say is this is an excellent idea!Easy to setup, works as advertised. Super cool product, I used it the other day to let a newcomer test one of my planes. Switching from one receiver to the other takes about half a second to switch from one receiver to the other.
Something to consider. Use a full-range receiver for the master and a park receiver for the slave if possible and not the other way around. So you can take over in case the plane flies out of range. A 5 channel receiver is needed for the master, since one channel has to be used for the receiver switching. (If you're using a 4ch plane)j'ai acheter j'ai eu du mal a le mettre en place sur mes 2 turnigy th9x mais je l'ai teste en vol avec mon fils comme lve cela fonctionne trs bien.
je ne regrette pas mon achat
je mis aussi un lien en video sur you tube du branchement et des divers teste effectuer sur ce boitier
installation dÃ©crite par EzÃ©chiel download now [135kb] Wiring Diagram download now [28kb] Buddy Box download now [0kb] Buddy Box download now [0kb] , CORRCT and EASIER! download now [99kb] rcd3022 download now [387kb] Buddy Box 4CH Wireless System Dual-redun download now [488kb] Wiring Diagram download now [386.84Kb]