Registrarse

Product Finder

Configuración

Useful links

 
[["US","AU","GB","DE"]]
Registrarse

2725 1600kv sin escobillas del motor Outrunner

2725 1600kv sin escobillas del motor Outrunner

Now save guardar 0,00 € 0,00 €

9,31 €
Sin existencias!
Stock:
OUT OF STOCK
Peso:
53 g
SKU:
074000063

Suggestion Box

Please let us know if you found any issues with this product listing.
We take our customer comments very seriously and in many cases our website modifications and product updates are a result of your comments!

Price War

If you've seen a product elsewhere for a better price, please let us know! HobbyKing pride themselves on offering the best price, so if there if you see something cheaper elsewhere, let us know!

Combine

essential items and
acc
Descripción
del

2725 1600kv sin escobillas del motor Outrunner

Especificaciones:
Dimensiones: 27 mm x 25 mm
Peso: 35 g
KV: 1600 rpm / v
Voltaje: 7.4v ~ 11.1V (2s ~ 3s)
Corriente máxima: 17A
Potencia máxima: 190w
Eje: 3 mm

* El color puede variar

Product
Specifications

Información adicional

  • SKU (Número de Referencia):
    074000063
  • Brand:
    N/A
  • Peso ( g)
    53.00
  • Longitud
    85.00
  • Ancho:
    27.00
  • Altura:
    70.00
  • Kv (rpm / v)
    1600.00
  • Corrientes max (A)
    17.00
  • Potencia ( W ):
    190.00
  • B Longitud ( mm ):
    20.00
  • Puede longitud D ( mm )
    10.00
  • Max Voltaje ( V )
    11.00
  • Un eje ( mm ):
    3.00
  • Unit Weight (g):
    N/A
  • C Diámetro ( mm )
    27.00
  • Longitud Total E ( mm )
    45.00
  • Resistencia ( MH ):
    0.00
Community
Discussions
Rate&
Review

Escribir Tu Propia Revisión

Only registered users can write reviews. Please, sign in or sign up

Quality
Value
Overall
Worked fine at first. Didn't take long to figure out there is a quality control issue with this motor. At about 3/4 throttle it came to a screeching halt. Drop throttle and start again with same results. Found out that the stator with the wire windings worked loose from the motor housing. At about 3/4 throttle it would start to spin on the housing and lose timing causing it to stop. All three of these motors i got do the same thing. So it wasnt just a fluke. I assume that separating the motor and glueing the stator on firmly will fix the issue. I am waiting for one to dry to test it.
Quality
Value
Overall
Quality
Value
Overall
good engine

put it on biks3

now learning to fly)
Quality
Value
Overall
Quality
Value
Overall
whatever Ive writen before - forget it - this motor is rubbish. Bearing becoming hot on 3S, one of two was burning by using an 8x6 prop. POS
Quality
Value
Overall
Quality
Value
Overall
nice little outrunner - bearings seems to be okay. easy to install - like shaft on both side.
Quality
Value
Overall
Quality
Value
Overall
It is good motor but where is motor mount? draw more current, gives less thrust compared to other motors in it's size. It is not bad motor but also not very good one, something in between.
Quality
Value
Overall
Quality
Value
Overall
Great little motor. Attached this my my makeshift hovercraft and worked a treat, plus the fact that it didn't cost a lot was a bonus.
Quality
Value
Overall
Quality
Value
Overall
Badly designed motor. They have decent grunt but the shaft is stupidly long at the rear and cannot be adjusted. You would think you can take the grub screws out and the housing the slide the shaft up? no.. took them apart... the stop of the shaft is fixed to the spinner, it's not sliding anywhere. They also have a chunky 4.2mm axl
Quality
Value
Overall
Quality
Value
Overall
I ended up with six of these. admittedly I crashed my quad and bent two of the props. But then today while hovering one of the motor shafts sheared off at the groove where the e-clip holds it on. Which by the way is where the other two bent.
Quality
Value
Overall
Quality
Value
Overall
Good motor for this price. I run it in a flying wing with 1000mm(39.4in) wingspan and
460g(14.8oz) weigth. Prop 8x4(fold). 3S 850mA lipo. Goes unlimited vertical and has
around 5min motor runtime.
Quality
Value
Overall
Quality
Value
Overall
Very nice motor although I couldn't slide the shaft through without fear of damaging it. It would need a thin firewall for attaching it behind the propeller.
Quality
Value
Overall
View all reviews
Upload
Videos
Upload video
Upload
Files

Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!

Customer files
DIY Hex using 2725 motors download now [156kb]

Combine

essential items and
acc

Etiqueta de Producto

Utiliza espacios para separar las etiquetas. Usa comillas simples (') para expresiones.