New Items Foro
Registrarse

Total Price

0,00 €

Cesta 0 Cesta 0 Loading...

2804-210Kv sin escobillas del motor del cardán (Ideal para GoPro Cámaras de estilo compacto)

2804-210Kv sin escobillas del motor del cardán (Ideal para GoPro Cámaras de estilo compacto)

Shipped From:
  • USA
  • Global
QTY:

Now save guardar 0,00 € 0,00 €

11,34 €
Estado:
En stock
Peso:
31 g
SKU:
047000029-0
WANT FREE SHIPPING? Click here to find out more!

Mirando para hacer su plataforma de video ultra-suave? Este es el propósito último en alta cuenta de polos sin escobillas motores construidos cardán lisas.

El motor 2804 viene con el montaje empotrado por lo que cualquier bricolaje para proyectos PRO son simples y directos, que también viene con el conector hembra estándar pre-instalado, así que el cableado es tan simple como conectarlo. Es una combinación perfecta para nuestra sin escobillas cardán Estabilización Junta y IMU.

El 2804 es el tamaño perfecto para las cámaras alrededor de 100-300 gramos (estilo GoPro).

Especulación:
Polos: 12N14P
KV (RPM / V): 210
Resistencia: 10.4omh
Peso: 35 g
Alambre: 0,19 mm
Torque: 240 g
Inferior central agujeros del centro: 16 mm y 19 mm
Arriba en el centro a centro de los agujeros: 12 mm

  • SKU (Número de Referencia) 047000029-0
  • Brand Other
  • Peso ( g) 31.00
  • Longitud 35.00
  • Ancho 15.00
  • Altura 35.00
  • Kv (rpm / v) 210.00
  • Corrientes max (A) 0.00
  • Resistencia ( MH ) 10.00
  • Max Voltaje ( V ) 0.00
  • Potencia ( W ) 0.00
  • Un eje ( mm ) 0.00
  • B Longitud ( mm ) 15.00
  • C Diámetro ( mm ) 34.00
  • Puede longitud D ( mm ) 10.00
  • Longitud Total E ( mm ) 15.00
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

Good motor, I use it for roll in a 3 axis gimbal, I enlarged the threads to 3mm though. very simple to do, just disassemble the rotor and insert a 3 mm tap, work slowly, add a bit of oil. No predrilling required. Assemble it back. Bought two, one had a minute play if you pulled on the rotor casing, just put it on a board of soft wood rotor down and slightly tap it with a small hammer on the shaft (circlip end, do not remove the circlip) checking for play. Adjust the hammer power by slightly increasing it if there's still play. Don't over do it!

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Good motor, I use it for roll in a 3 axis gimbal, I enlarged the threads to 3mm though. very simple to do, just disassemble the rotor and insert a 3 mm tap, work slowly, add a bit of oil. No predrilling required. Assemble it back. Bought two, one had a minute play if you pulled on the rotor casing, just put it on a board of soft wood rotor down and slightly tap it with a small hammer on the shaft (circlip end, do not remove the circlip) checking for play. Adjust the hammer power by slightly increasing it if there's still play. Don't over do it!

I used these for a decently heavy 3D printed gimbal of my own design. The camera housing weighed 325 grams and these motors worked fine, but was nearing the threshold of over-drawing the 500 mA max that the Tarot gimbal control gives. I tried to use these motors on a 425 gram camera and they would not stabilize the gimbal within the 500 mA allowance of the gimbal controller.

If you decide to design your own gimbal, these will work great on cameras in the 100-300 gram threshold. Remember that gimbal design is mostly about balance than it is about torque. Also, the more jostling your quadcopter or craft does, the more torque you have to put out. So, test your stuff on the ground liberally before flying it!

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I used these for a decently heavy 3D printed gimbal of my own design. The camera housing weighed 325 grams and these motors worked fine, but was nearing the threshold of over-drawing the 500 mA max that the Tarot gimbal control gives. I tried to use these motors on a 425 gram camera and they would not stabilize the gimbal within the 500 mA allowance of the gimbal controller.

If you decide to design your own gimbal, these will work great on cameras in the 100-300 gram threshold. Remember that gimbal design is mostly about balance than it is about torque. Also, the more jostling your quadcopter or craft does, the more torque you have to put out. So, test your stuff on the ground liberally before flying it!

these motors should have high quality bearings with no clear ens to the axles images are shaky and a lot of wobble, my next motors will be of a higher quality

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

these motors should have high quality bearings with no clear ens to the axles images are shaky and a lot of wobble, my next motors will be of a higher quality

meka kama nahe podi e ne neda

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

meka kama nahe podi e ne neda

I bought 6 units of this motor and only 2 of them work. The windings are open on the rest. Hobbyking needs to improve quality checks ASAP ! I also bought 3 controller boards and 1 unit came with a DIODE bad. Had to replace it myself.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I bought 6 units of this motor and only 2 of them work. The windings are open on the rest. Hobbyking needs to improve quality checks ASAP ! I also bought 3 controller boards and 1 unit came with a DIODE bad. Had to replace it myself.

Perfect motor for GoPro H3 (Roll-axis). Buy the smaller motor for pitch.
Smooth and silent. Very happy with mine.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Perfect motor for GoPro H3 (Roll-axis). Buy the smaller motor for pitch.
Smooth and silent. Very happy with mine.

enfin ces moteurs chez HK , la on va pouvoir ralis ces propres nacelles a moindre cot comme d'habitude chez HK.
merci

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

enfin ces moteurs chez HK , la on va pouvoir ralis ces propres nacelles a moindre cot comme d'habitude chez HK.
merci

Customer files
047000029-0 -43040.JPG Download [81]
Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!

Related Tags

Combine Essential Items and Save