BA BL1230 4200kv sin escobillas del motor Inrunner
Pesar: 13 g (0,46 oz) de
Dimensiones: 12 mm x 30 mm (0.47in 1.18in X)
Diámetro del eje: 1,5 mm (0.059in)
Sin corriente de carga: 0.4A
Corriente de carga: 6A
A su vez: 20
SKU (Número de Referencia):
Peso ( g)
Kv (rpm / v)
Corrientes max (A)
Potencia ( W ):
B Longitud ( mm ):
Puede longitud D ( mm )
Max Voltaje ( V )
Un eje ( mm ):
Unit Weight (g):
C Diámetro ( mm )
Longitud Total E ( mm )
Resistencia ( MH ):
- SKU (Número de Referencia):
Fits my losi micro crawler perfect. Has about the same speed as the stock motor but about 6 times the torqure. I can get almost no motor heat running it full bore on a 2 cell lipo on a 10A ESC. Two thumbs up for sure. Motor wires are a bit long and thin but I'm sure that's to save on weight. Longer run times too.Works killer in my losi micro crawler. Has way better torqe and amazing throttle control at low speed. Its about the same speed as the stock motor to. You will have to drill out a different hole on the motor mount but that's it. Fits great and I have no heat issues at all with a 2 cell lipo on a ten amp ESC. Overall its working great so far and I can see it working good for years to come.tinky, neat and hot Motor. SweetI got this after my losi micro sct 1/24 brushless motor died 3 different times (warranty). It's been a strong little motor. Had to drill two holes in the motor mount and moved the on/off switch to the top. It's slightly longer by 10mm.
Small and very fast. It is very qualitatively made.
For small models that is necessary.
7-12 volt perfectly works.
To all I recommend.Great little motor - using this on a Eagle 50 (aka Walkera 22e) direct drive tail with a Esky Tail Blade Set 002386.
The tail balde is the same as the BLADE EFLH1321, GWS 3x2 prop and also the HCB-03 from HobbyKing. I got a
BLADE EFLH1321 mount and flipped it 180 so the the air flow is across the motor and with the addition of a heat
sink the motor runs much cooler. I paired it with a Tz12A HobbyKing 12A BlueSeries brushless controller plugged into
a walkera RX-2609 receiver that had the gyro mod (gyro board removed and gyro-sense jumper to AUX2). Make sure you
get the blade on the right way, it does not work as well when running backwards. Ask me how I know... Also it uses
M1.6 mounting screws and it does not come with them and hk does not carry em either.Can this be used in the Parrot AR.Drone x 4 as an upgrade? Has anyone used these motors in this application? Stock motor is 3500kv this would increase power output/consumption, but will it work with onboard computer/esc profiles......I will order 1 to find out, the replacement from Parrot = 70.00us$, if your esc is still good this is 15.00 plus ship or 60.00 for all 4 ship......may as well upgrade for the price of one stock motor x4 :)Nice little motor used in a Multiplex Fox conversion (motor mounted on Pylon over fuselage) Thrust about 75 gram with GWS style 3x2 prop on a 2s lipo battery. A 3x3 prop loaded it up too much and did not get same level of thrust on 2s.
Great motor awesome power I have this on my adrenaline rush and it will do aprox 80mph. very durable and reliable as well.tres puissant. le shaft est tres court est est tres fragile. il se courbe facilement