Una excelente parkflyer dimensionado EPO chorro. El chorro de BAE Hawk FED entre 90% pre-construido, basta con incluir su propio motor sin escobillas, servos, ESC, la batería y el equipo de radio (Tx / Rx). Se necesitan 3 x 9g servos, uno para el ascensor, uno para los alerones y el otro para la rueda de nariz orientable. Debido a que el chorro de BEA Hawk está hecho de EPO, es muy resistente a la rotura y, literalmente rebotar en choques ligeros. El material también es fácil de reparar y bastante flexible.
Volar Peso: 630 g
Motor: 2826 3200kv (Obligatorio)
ESC: 25A (Obligatorio)
Servo: 9g * 3pcs (Requerido)
Batería: 1600mAh 3S1P 20C Lipo Pack (Obligatorio)
EDF Diámetro: 70 mm (incluido)
Necesario:Su propia TX y RX (con V-tipo de mezcla)Motor: 2826 3200kv
Servo: 9g * 3pcs
Batería: 1600mAh 3S1P 20C Lipo Pack de
SKU (Número de Referencia):
Peso ( g)
- SKU (Número de Referencia):
I bought one placed a 3200 4s battery and a doctor mad thrust 70mm 11 blade edf. Turnigy 60 amp esc had to trim the foam cover a little for fit. Added 3 quarters of an ounce of weight at the rear. She flies amazingly stable. Able to fly her in 15mph wind gust no problem.Great plane,
price performance better you can find.
I have used it with 12 blade fan, great! but is good also with orginal fan.
I have modified it with retract.....Just maiden this plane today.. its need 4 cell setup edf.. i have use chengsun 6 blade edf 2800kv motor. Fly very wellVery pleased with performance of this model (after a few modifications) I've upgraded the fan and motor which required the engine hatch to be cut larger to accommodate longer more powerful edf motor. Now getting about 4 mins flight with 3000mah battery and ten blade fan unit. I found the elevator push rods to be awkward to fit alongside wiring in upper fuselage so cut servo holes and mounted a small servo on each side to activate elevators. Model flies very smoothly but dual rates will probably be needed on elevator. There is no prop wash the elevator authority is limited when trying to land with little power. My first EDF and I'm well pleased with itNice model for the price but instructions very poor. A suggested COG position would have been nice. I fitted original fan with motor suggested but balance of fan was a bit out despite my attempts to balance it. Power was also limited so I upgraded fan and motor and opted for 4s system with 12 bladed fan. Time will tell if it was a wise move. ( Yet to fly it ! ) Nose cone is very thin and spoils the overall appearance of what is otherwise a nice looking model. Also chose to fit two 9g servos instead of Y shaped push rod which I considered may get caught up in the esc / motor harness. A good model to do a bit of edf testing.ciao Gianhulk ho lo stesso modello , ho volato con 6 celle pero , due da 3 celle da 2200 perche non potevo indetreggiare le batterie in quanto al centro c il telaio di legno. tempo di volo 3 minuti .PUOI mandarmi qualche foto o video di come sono messe le batterie? ciao graziei think this jet is amazimg..(amazing price, flight character,...etc)
it can fly very slow speed and easy to fly, in other word the max speed is not your expectation ,(i not sure what speed is lowest speed. just could fly stable in lower speed)
my set up is stock fan, 2836-3200kv turnigy motor, 55A dlux esc(too heavy & over spec' perhaps 40amp esc is enough) and 3s 2200 35c~ lipo, modify rudder system. Total weight is about 920g(include 200g battery),
It was possible idle thrust landing as lower wing scale model plane
In spite of many positive things there are few negative things 1st of all nose cone is flimsy,2nd landing gear steel rod bended every takeoff & landing, 3rd stock fan is very weak & unbalanced, 4th edf maintenance hatch too small. have to cut rear fuselage to esay access(advenced edf unit can't install without cutting fuselage)
After maiden flight i decided to mod power system ( will chang esc 40A and Fan unit & motor) becouse of stock fan was break into thousands pieces and vomit the pieces from the air intake...
very good Quality, easy to fly and good to land on grass without Landing Gear!muy buen entrenador,primer avion que vuelo , y perfecto, y excelente precioVery well packed, nice size Aeroplane.
Finish of the foam is also very good.
Like many other purchasers of the plane the red nose cone is missing.
I would have thought that with the amount of missing nose cones Hobbyking would check these kits before dispatch.
No File Name download now [49kb] Hawk Nose Cone Strengthen! download now [5694kb] No File Name download now [458kb] Replacement stickers download now [435kb] The size download now [64kb] No File Name download now [34kb] On the ground download now [182kb] In the air download now [27kb] In the air download now [26kb] Wing Reinforcement download now [352kb] Battrey bay with 3,000mAh 4S download now [445kb] Battrey bay with 2,200mAh 4S download now [410kb] Battery cooling suction holes download now [346kb] Dougs colour scheme download now [435kb] No File Name download now [458kb] with 7075 Alloy Shock Absorbing Strut download now [2584kb] Intake Upgrade download now [1.73Mb] EDF Upgrade download now [469.94Kb]