BMS-621 mg velocidad Servo alta (Metal Gear) 6,4 kg / .13sec / 47gEl servo viene con un paquete de accesorios de servo y se hace con un caso de servo de alta resistencia, el servo está diseñado para aplicaciones de alto rendimiento del coche R / C. Doble cojinete de bolas con goma flexible resistente al agua, de lo contrario la curva de selección ourput es igual con Futaba 25 dientes.
Este servo viene con JR / Hitec S Conector también conocido como un "conector universal". Incluso pensó que esto viene con servo JR / Hitec S Conectores, este servo es eléctricamente compatible con receptores Futaba.
1. engranajes de metal
2. Arte curva con suave.
3. cojinete de bolas de doble M9.6 (si-aceite)
4. 3 polos fuerte par del motor con baja señal afectan el éxito y obtener la certificación CE.
5. caso apropiado de goma para prueba de agua
6. Lo mismo con Futaba estriado 25 dientes
7. caso servo trabajo pesado
Peso: 47 gramos / 1,66 oz
Dimensiones: 40,5 x 20 x 38,5 mm / 1,60 x 0,78 x 1,54 pulgadas
Torque a 4.8V: 6,4 kg-cm, el 89 oz-pulg
Torque a 6.0V: 7,2 kg-cm, 109 oz-pulg
A velocidad de 4,8 V: 0.13 sec / 60 ° sin carga
En 6.0V Velocidad: 0.10 sec / 60 ° sin carga
SKU (Número de Referencia):
Peso ( g)
Velocidad ( Sec / 60 grados )
Par ( kg ) ( min . 0,01 kg )
Unit Weight (g):
A ( mm ):
B ( mm )
C ( mm )
D ( mm ):
E ( mm ):
F ( mm )
- SKU (Número de Referencia):
I have installed this servo in my 2,6m 3d model as a gas sevro. After 20min of good work on the ground (while I was trimming a model) IT BURND!!! well, good that happend not in the air , not recommendedI've been using these for years in my yachts for rudder control and had only one fail.
I sail in salt water and have had boats flooded, but I pack top gearbox with thick lanolin grease, add 'O' ring onto shaft, coat with liquid electrical tape (rubber compound) and they are bullet-proof. I use them in all my yachts. Great power, good centreing, tough and low power consumption.Bought 5 for a seagull models mxs-r, all 5 initially looked very good, however, last night the throttle servo melted down, literally, lots of smoke and melted plastic. Fortunately the airframe was on the bench and not in the air. I have read other reports of BB servos melting down, I'll be pulling the rest and bench testing them for an extended period of time.This bluebird BMS-621MG servo is very nice for the price. Quality seems great and speed/torque are quite good and more than adequate for on-road use like I use it. I can highly recommend this to everone.Ive brought 2 of these servos now and they both work perfectly! nice and fast and center every time, im using them on 1/10 drift cars with a 6v bec, i will be using the hi torque version in my scx10 trail truck when it shows up they are the best bang for buck around!it came very well packaged and with all the screws and arms. it gives 6.4Kg @ 4.8V and can withstand 6V. Great for RC car and planeFor the price this servo has a lot of torque and is very fast. My only complaint is it does not center well. Very good for a basher 2wd off road car steering or off road nitro throttle on a budget.I purchased two that run in my 1/8 scale buggy. Good torque, centers great, and noticeable quick speed. I ordered two more to replace my steering servos in my 1/10 scale nitro touring car and 1/10 electric touring car.That it is what i call a very good servo. it is very fast, Reliable and cheap! I used it in my SC10 truck and now it is my rc drift car =)
I have no problema with this servo. I will buy more....Purchased 9 of these servos and 3 burned out during installation. I didn't expect to find that 30 percent of these servos were faulty