C2222 Micro sin escobillas Outrunner 2850kv (15 g)

• Overall
• Quality
• Value

Nice little motor

Nov 16, 2016

I am running a couple of these on 3S setups and 5x5 props on a flying wing. I checked today and it is peaking at 20A so obviously too much prop. It is getting too warm also. So far, a dozen flights and it is still running. I will drop the prop down to around 4x4 and hopefully get the power in a better range for this little motor. I like it.

• Overall
• Quality
• Value

Nice little motor

Nov 16, 2016

I am running a couple of these on 3S setups and 5x5 props on a flying wing. I checked today and it is peaking at 20A so obviously too much prop. It is getting too warm also. So far, a dozen flights and it is still running. I will drop the prop down to around 4x4 and hopefully get the power in a better range for this little motor. I like it.

• Overall
• Quality
• Value

Customer Rated

Nov 30, 2015

Mini Zagi

Envergadura 80cm Peso 257gr C2222 Micro brushless Outrunner 2850kv GWS EP Propeller (DD-4040 102x102mm) black ESC 18-20a Lipo Nano tech 1000a 25-50a.
Todo en Hobbyking

https://www.youtube.com/watch?v=MZc4x7z-Nlk

• Overall
• Quality
• Value

Customer Rated

Nov 29, 2015

https://www.youtube.com/watch?v=MZc4x7z-Nlk

Mini Zagi

Envergadura 78cm
Peso 257gr

C2222 Micro brushless Outrunner 2850kv
GWS EP Propeller (DD-4040 102x102mm) black
ESC 18-20a
Lipo Nano tech 1000a 25-50a
Hobbyking

• Overall
• Quality
• Value

Certified Buyer Rated

Sep 09, 2015

Nice motor be carful to the wire while you turn them back

• Overall
• Quality
• Value

Customer Rated

Jul 04, 2014

It overheads with 3 cell. Also hard to keep prop on. 4.75 x 4.75 prop is a bit much pushing wing wing. Wish this set up a #41 o ring works.

• Overall
• Quality
• Value

Customer Rated

May 27, 2014

Propeller used disintegrates easily with the o-ring used. Risky during testing, I wish there is better shaft design to install the props.

• Overall
• Quality
• Value

Customer Rated

Apr 05, 2014

If you have holes bottom and front to cool it, no problem keeps fresh at 8,5 amps
with a stock of mine prop 5X3.5 : 200g pull and 8.5 AMps with 2 cells.
Prop saver is inadequate (for my stock props only) and CANT BE REMOVED : its part of the rotor.
You can use the back side because it has a 2 mm diameter by 5mm length at the stator.

• Overall
• Quality
• Value

Customer Rated

Dec 10, 2013

Hello,I replaced the stock motor on my mini swift with this one after I rebuilt the motor mount with a birch ply mount.Today I corrected the center of gravity by moving the battery back into the fuselage after removing the hump on the bottom of the fuselage.Maiden flight was successful and plane is fast even at half throttle.C2222 isa great little motor so far.Mike

• Overall
• Quality
• Value

Customer Rated

Oct 24, 2013

The bearings in this grind. I doubt that it's my fault. Not happy with it - and it isn't really powerful enough for the bonsai for my tastes. It won't go vertical. It gets hot on 2s with a 5030, but that's probably because of the bearings.