Esta brillante enchufe y volar PAC viene con toda la electrónica PREINSTALDO haciendo para una construcción increíblemente rápido. Proporciona un modelo excelente habilidades acrobáticas más que compensar por ello no es apariencia bastante escala. enchufe de balsa y mosca no es algo que se ve a menudo y tanto trabajo que se ha hecho para usted que 1-2 horas máximo es todo lo que van a necesitar para entrar en el aire. El potente motor outrunner, ESC y todos los de servo son pre-instalado que le deja a pegar en las plumas de la cola y el perno del ala en.
Hemos probado y volado esta PAC bastante y es increíblemente capaz, con impresionante empuje del motor de baja kv y una gran combinación prop SF. La década de los servos son más que hasta la tarea de mantener las superficies de control impresionantemente grandes que apuntan en la dirección correcta y el modelo es práctico con sus alas extraíble, que cubre muy bien aplicado que es bueno para la orientación y el chasis robusto. Si usted está harto de espuma, pero le gustaría una pequeña-ish, fácil de construir y modelo acrobático muy capaz, esta diversión, barato CAP 232 es sólo el billete!
Longitud: 885 mm
Carga alar: 32gdm2
Área de ala: 20.9dm2
Volar Peso: 650 g
Servo: 9g x 4
ESC: 30A w / BEC
Motor: 4006 sin escobillas Outrunner 900kv
Su propio canal 4 de TX / RX
Batería 1300mAh ~ 2200mAh 3S Lipo
SKU (Número de Referencia):
Peso ( g)
- SKU (Número de Referencia):
Ok built. I recommend it being re-enforced with super glue, as it is pooly glued.
The plane flied great.
Motor is good quality
-NO SPARE PARTS AVAILABLE
-Besides the Motor, ALL THE INCLUDED electronics are low quality. ESC WILL burn out on you eventually in mid flight. This happened to me and other people. There are videos of it.
If you decide to buy this, I recommend you replace all the electronics besides the motor, reinforce with more glue, and hope to not crash because there are NO parts available for it.
For this, despite the fact that it flies great, I regret buying this plane. The ESC failure set it on fire in mid air and I lost my $150.0...
This plane was a nightmare to build, It could not be considered pnp. All the servos were loose as they were screwed into places where screws can not grip. All the servos were glitchy and needed replacing, even the screws holding them were rusty. The prop nuts were also rusty and all the wiring plus the ESC needed replacing. One push rod was also missing. If I didnt have a large amount of spare parts on hand this plane would never have flown.It seems missing pushrods in the pckage is a common problem. I had mine delivered last year. Just finally found time to open the box and assemble this baby. All in all the model seems capable enough. The build quality is good. The servos are nameless and look a bit cheap though. The control surfaces look quite big. I wonder if it can do 3d.
Yesterday i did a ground test. The motor ran for 3 minutes on full throttle with 2s 1800mah battery. I will be getting a 3s 2500mah at least for the maiden flight. That happens after two weeks when I am back home from work.Very nice plane, but be careful mine has the right COG without the battery, so if I put the battery in battery case, cog is more than 10 mm forward so very nose heavy. I put the battery under the cockpit for a good COGVery nice plane, but it took 2 week to package before it was shipped...
Was missing a pushing rod in mine too.
My first balsa plane, very happy with it. After been assembled, with a 1500 mAh battery, it was very nose heavy (cog 10 mm forward, 79mm from the edge of the wing instead of 89mm). I broke the battery compartiment to put the battery vertically, and then the cog was right. Go vertical very easyly, and had take some hard landing, but stay strong! Yesterday I broke the landing gear sock, but some epoxy and all is like brand new!
A good plane!Great overall performance. Great craftsmanship!
Flys amazing regardless of finding the right cg.
Hovers well with a little extra weight on the tail. Remove the tail wight and you have an incredible sport flyer.
Thanks hobby king! ABought this plane when on special late last year. Unfortunately it arrived in New Zealand damaged, took photos, scanned HK paperwork and followed HK compalint proceedure, They got matter all sorted form me quickly and very much in my favour. Full marks to their customer service.
Havent flown the plane as keeping as replacement for when my HK Pitts Special falls apart or perishesMine arrive a couple of days ago. Thank you Hobby King for double boxing. The outer box had a 12 inch crease on the boxt and if not for double boxing the plane would be a right off. Plane very good but it has a lot of plastic parts. A large plastic cowl. It has a large cockpit window and the plastic goes all the way to the nose.Lots of bits missing from mine , only one pushrod , screws missing , and as usual the clevices where rubbish , DO NOT USE THE PLASTIC CLEVICES the little plastic pin snaps off immediately
I havent flew this yet so will not comment on how it flies, not sure how long the motor and esc will last, and the servos are also crap.Yust received this plane, everything looks great.
But it is not plug and fly!!!
There is too much to to! It is like other ARF models. Ok, the electronics are included and mounted, but no servo horns, push rods, hinges for elevator and rudder...