HD1610-3400KV interior / Perfil / F3P Outrunner Motor

• Overall
• Quality
• Value

Customer Rated

Jun 15, 2015

Not happy with this motor. I purchased 2 of these in tandem with the plush 6A ESC. They often fail to run, oscillating for several seconds before finally spinning. I tried changing ESC's without success. I ran other motors with the same ESC with success. So it is evidently the motors.

Not going to use these again.

• Overall
• Quality
• Value

Certified Buyer Rated

Feb 11, 2015

??????? ?? ??? ?? ? ??????. ?? ??? ?? ??? ?? ??? ??? ?? ???? ????.

• Overall
• Quality
• Value

Customer Rated

Dec 03, 2014

I purchased 5 of these motors, The bearings failed after only 5 flights, This would be a good motor if they only used high quality bearings. I replaced the first failed motor with another and the bearings failed after 6 flights. In both failures I was using a properly balanced prop with a 2s lipo.

• Overall
• Quality
• Value

Customer Rated

Nov 09, 2014

I run 2s 5030 w/ 6a plush on 100g airplane. I would recommend a AUW if 80g or less. 3s was too much for this motor! Quality built, but needs to come w/ screws as mounting it was a pain... tiny motor!

• Overall
• Quality
• Value

Certified Buyer Rated

Sep 19, 2014

Ein richtiger Winzling, Achtung Schraublcher sind sehr klein < 1mm, und im Lieferumfang sind auch keine dabei.

• Overall
• Quality
• Value

Customer Rated

Sep 28, 2013

Awesome little motor, packs a very good punch on 2s batts and a 5x3 it will surprise you how much grunt it has. Well made and shows quality but a bit expensive. I bought two and looking to buy another two when back in stock.

• Overall
• Quality
• Value

Customer Rated

May 11, 2013

Very happy with this motor, for such a light (6.5 gr) motor it produces lots of power with 2s batts and gws 5030 props. Truly a joy to fly my 70 gram AUW Underball 14" with this motor, good magnets and decent quality.
Responds very well to throttle, revs up quickly.

You'll need 1x4mm self taping screws as the mounting holes are very, very small. I wouldn't make them bigger and weaken the arms. 1x4 screws are fine.

Not cheap but worth the money, would def recommend this motor for up to 80 gram AUW models for lively performance. Maybe heavier ones too but would loose the punch these DO deliver.

• Overall
• Quality
• Value

Certified Buyer Rated

Feb 23, 2013

Motor Gesamtlaenge 17mm, Befestigungsloecherradius 10mm, Bohrung 1mm,

Aufnahme fuer LS 4mm Durchmesser,

Gewicht 6,27g mit 5,5cm Kabel

O-Ring Gewicht 0,11g Innendurchmesser 8,5mm

• Overall
• Quality
• Value

Customer Rated

Feb 05, 2013

Very good motor, strong magnets, build in a small 3d indoor flyer.

Much power with 5x3 slowfly prop. Motor becomes just slightly warm after 5 minute 3d flying with a 2S 270 nano tec lipo.

Delivered rubber rings are too small.

I will buy more of this motors.

• Overall
• Quality
• Value

Customer Rated

Jan 30, 2013

good things : Nice motor.
i get a litlle more than 100gr of trust with 5x4.3 GWS and 4.3A 2S
(this getting the motor hot and smelly I didn't recomanded more than few second)

bad things : I don't get any prop saver band in my package :-/