Registrarse

Product Finder

Configuración

Useful links

Chat en vivo
 
[["US","AU","GB","DE"]]
Registrarse

Power Module HKPilot con conectores en T y 6 pines cable de 150mm

Power Module HKPilot con conectores en T y 6 pines cable de 150mm

Discontinued Product

Please continue searching for a similar product.
Stock:
OUT OF STOCK
Peso:
42 g
SKU:
9387000031-0

Combine

essential items and
acc
Descripción
del

El módulo de alimentación HKPilot 2.5 incorpora tanto una manera de alimentar su HKPilot y los accesorios y reportar el voltaje de la batería y la corriente a la HKPilot, esto puede ser visto en los registros almacenados de la HKPilot o vivir con una radio telemetría. A lo largo de un cable de 6 pines sola y firmemente incluido que coincide directamente el conector de la HKPilot. El regulador de conmutación salidas de 5.3V a bordo en un máximo de 2.25A, y se puede utilizar hasta 18 voltios (4S LiPo) y en un máximo de 90 amperios. El módulo de alimentación está listo para usar con conectores en T preinstalados, y reducir el tamaño ajustado para protección.

Nota: El módulo de alimentación tiene una potencia de 2,25 amperios para alimentar el HKPilot, el receptor y los periféricos (GPS y radio telemetría) SOLAMENTE. Para poder utilizar un CES servos con un BEC adecuada o un independiente BEC enchufado en el bus de salida, y quite el puente 1 para aislar las dos líneas de alta tensión.

Presupuesto:
Voltaje de entrada máximo: 18V
Max detección de corriente: 90A
Las salidas de conmutación del regulador: 5.3V 2.25A al máximo
6-pos cable Molex se conecta directamente a HKPilot
Medida de tensión y de corriente configurado para 5V ADC

incluye:
DF13 150 mm Conector 6 Posición larga
Power Module HKPilot con conectores en T

Product
Specifications

Información adicional

  • SKU (Número de Referencia):
    9387000031-0
  • Brand:
    No
  • Peso ( g)
    42.00
  • Longitud
    100.00
  • Ancho:
    15.00
  • Altura:
    40.00
Community
Discussions
Rate&
Review

Escribir Tu Propia Revisión

Only registered users can write reviews. Please, sign in or sign up

verified_user Quality
trending_up Value
playlist_add_check Overall
While the 5v output of this module should be 5.25v, this module is actually outputting 5.50v. The pixhawk/hkpilot board detects this overvoltage condition and faults the board.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Soldering quality is disgusting! If you're planning to use the cables/ T connectors, do yourself and your craft a favor by re-soldering them.

On the positive side, it works beautifully and the DC-DC converter piggyback board is of great quality.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Works as advertised.
I replaced the input T connector with XT60 and soldered directly to the PDB the output wires. Nice thick 12awg wires.
For Arducopter I had set a value of 17Amps/volt but I think 12-13A/v should be better.
The 5V SBEC was kinda in my way, trying to fit it inside a Trifecta frame, where the PDB is, so I removed it, connected it with wires (looks like only 4 out of 5 pins are used) and placed the regulator somewhere else.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I am using this on the HKAPM micro, with slight modification to the cord. It worked right out of the box, with minimal setup through the Mission Planner software.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
BE CAREFUL and check this Power Module before installing. I installed without checking and immediately smoked it. After the smoke cleared I found the positive (Red) and negative (Black) leads on the output side were reversed. The Red lead was actually negative and the Black lead was positive. The input side was wired correctly.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Cosa posso dire e un power module
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
WRONG CABLE!!!!! the cable you see in the picture and actually shipped with the kit, does not fit the hkpilot board connector...... you can tell me what to do ????
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I had to get the one with T connectors ...So a bit of soldering for me .

BUT

EVERYONE SHOULD DOUBLE CHECK THE SOLDERING ON THESE AND Really TAKE 5 MINS TO REDO THEM .

Otherwise perfect Item cannot miss the amp/volt readings any more
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Get this one if you don't want hassel of powering up the board and you get the voltage data for FPV as a bonus!
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
bought this to go with the HK apm board which was working fine for more than a week. when this module arrived I plugged it in and at first all was OK but after about 10 connections the module failed with low volts out the sbec and took out the APM with it so I now have $100 of scrap electronics. In fairness to HK the sbec was a sub component made by a reputable US company.
verified_user Quality
trending_up Value
playlist_add_check Overall
View all reviews
Upload
Videos
Upload video
Upload
Files

Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!

Customer files
Pin layout download now [170kb]

Combine

essential items and
acc

Etiqueta de Producto

Utiliza espacios para separar las etiquetas. Usa comillas simples (') para expresiones.