Registrarse

Product Finder

Configuración

Useful links

Chat en vivo
 
[["US","AU","GB","DE"]]
Registrarse
Shipped From:
  • USA

HobbyKing 1608 sin escobillas 5900KV Outrunner

HobbyKing 1608 sin escobillas 5900KV Outrunner

Discontinued Product

Please continue searching for a similar product.
Stock:
OUT OF STOCK
Peso:
22 g
SKU:
HK1608-5900
Descripción
del

HobbyKing 2403 sin escobillas Outrunner 5900kv


Especificaciones.
RPM / V: 5900Kv
Recuento de Células: 1s Lipoly
Max.efficiency: 76,0%
Corriente en Max.eff: 1.5 ~ 2A
Max.current: 12A
Sin corriente de carga: 0.3A / 3.7V
Resistencia interna: 375mOhm
Dimensiones (Dia.xL): Φ16mm × 8 mm
Eje: 1.5mm
Peso: 7 g

Product
Specifications

Información adicional

  • SKU (Número de Referencia):
    HK1608-5900
  • Brand:
    N/A
  • Peso ( g)
    22.00
  • Longitud
    0.00
  • Ancho:
    0.00
  • Altura:
    0.00
  • Kv (rpm / v)
    5900.00
  • Corrientes max (A)
    12.00
  • Potencia ( W ):
    44.00
  • B Longitud ( mm ):
    7.00
  • Puede longitud D ( mm )
    5.00
  • Max Voltaje ( V )
    4.00
  • Un eje ( mm ):
    1.50
  • Unit Weight (g):
    7
  • C Diámetro ( mm )
    17.00
  • Longitud Total E ( mm )
    16.00
  • Resistencia ( MH ):
    375.00
Community
Discussions
Rate&
Review

Escribir Tu Propia Revisión

Only registered users can write reviews. Please, sign in or sign up

verified_user Quality
trending_up Value
playlist_add_check Overall
decu la fiche du moteur n est pas dessus comme le montre la photo faut se debrouller pour faire connection point negatif
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
So this little motor is about 6.2g and does deliver on what it says as power, however this little motor is power hungry. I have been using this motor with a 1 cell 160mah 25c and a 4.5x3 prop. I get about 50g of thrust and a flight time of only 2 1/2 minutes if I run full throttle. Running full throttle, a 3a esc stays cool but the battery does warm up.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
OK so the vibration is coming from the two screws in the prop adaptor, Take them out vibration goes away. I used 1 cell 160mah, 3A ESC, 4.5x3 prop. Im guessing based off the weight of my plane, 50g of thrust and 2.5-3A draw for a flight time of only 3 minutes. 4 crowns in quality only because of the prop adaptor screws. they need to be very carefully centered.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I was delighted when I opened this little motor. I love the backplate with mounts and wire protection built in. I also love the built in prop saver.



I spun it up with a fully charged 300mAh 1S battery on a HK 5A ESC and it didn't start but just jittered. With a hand start at 10pcnt throttle it started up but there was vibration. WOT without a prop was pulling almost 1A. WOT with a 4x2.5 was 2.5A. Sounds about right but the RPM was not there.



I tested continunity on the winds and it doesn't seem to have a short or a broken wire. Then I looked inside the bell and noticed a strange arrangement of magnets. The motor runs with a 9 pole stator and 12 magnets in the bell. Very common. The magnets were arranged in three groups of 4. In other words, four magnets aligned side by side, then a space, then 4 more, then another space... etc. I think this accounts for the poor efficiency. The magnets are glued into place (very common) but there was a puddle of dry glue on one side of the bell. That would account for the vibration.



I think this motor is better engineered than others in this size and weight, but the assembly needs some adjustments. Hopefully HK will improve future releases.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
this motor does not produce the same amount of thrust as a parkzone/ eflite musyang motor. it draws more current and makes less thrust than the 8.5mm coreless, brushed mustang motor and gearbox. disappointing.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Engine is made well, Prop holder is not removable. Hole on mounting plate (approx 3mm) is necessary for shaft. 4 starts for vibrations even if sticker was removed.
verified_user Quality
trending_up Value
playlist_add_check Overall
Upload
Videos
Upload video
Upload
Files

Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!

Etiqueta de Producto

Utiliza espacios para separar las etiquetas. Usa comillas simples (') para expresiones.