HobbyKing Ventus 2.3m OEP planeador (KIT)

• Overall
• Quality
• Value

Customer Rated

May 18, 2013

michael 5 points - 14/05/2013

summary of building notes and Hobby King - The basic body and wings were great the fitting out was fine but the niggles of no instructions and no way of fixing horns was frustrating,hence my effort to write same. I contacted Hobby king re monor shortages on another kit and had no response.Am I writing on here to be ignored.I see on the RTF site that overheating was a problem and the modeller concerned was cutting holes in the fus and was considering fitting a smaller prop/ Will my *85 receiver melt and is hobbyking aware of this and if so what are they doing. They have a duty of care and could be liable in law 'not fit for purpose'.I await answers. What a shame when it is a good looking well produced body shell,spoilt for need of testing and a few coppers to make it an excellent kit.

michael 5 points - 13/05/2013

as promised building notes The Hobbyking 'Ventus' 2.3 metre powered sailplane. Purchased as a kit April 2013 approximately *50 sterling. Building Instructions :- First of all check the components and ensure with a dry run all the component parts are there. 1 . fit all the servo,s 4 in the wing need special care as is would be easy to cut through into the upper wing. Next fit the elevator servo 9mg for the rudder and the 15g servo for the retract wheel on the ply board as cut out. Cut and fit the snake link and epoxy i

• Overall
• Quality
• Value

Customer Rated

May 16, 2013

Kam mit gebrochenem Seitenruder bei mir an. Achtung: in die 4 Aussparungen im Flgel passen keine 9 Gramm Servos, hier mssen 5 Gramm Servos zB: HXT500 eingebaut werden. Ansonsten macht der Segler bisher einen guten Eindruck.

• Overall
• Quality
• Value

Certified Buyer Rated

Mar 27, 2013

Perfecto velero para el precio que tiene.Es un poco rapido para los tipicos veleros, te da posibilidad de hacer muchas maniobras con el.El unico pequeo inconveniente es que viene sin instrucciones de montaje,pero es muy simple, requerira de algun ajuste segun los servos que se vayan a utilizat pero en general muy buena relaccion calidad precio.

• Overall
• Quality
• Value

Customer Rated

Mar 14, 2013

Took the plunge even after hearing HK model purchase horror stories. I dropped the money for the kit version and overall am very pleased. Model arrived quickly from US warehouse double boxes all parts sealed in plastic along with cardboard inside the box separating larger parts from each other and inflatable shipping pillows inside. Excellent packing!

Opened the model all parts are complete and all foam parts of the plane are in excellent shape and look very sturdy my first impression was "wow this was only $64 dollars". Will start assembly when I get the correct prop adapter for this.

The prop adapter it comes with is larger than the motor suggested in the combine related items window. That motor has a 3mm shaft the spinner included in kit is for 3.17mm. That is about my only complaint with this kit, and a slight mishap with a cutting knife on one side of the canopy, which I can really live with. Well worth the money and I'd make the purchase again even knowing what I do now.

• Overall
• Quality
• Value

Customer Rated

Mar 10, 2013

GOOD NEWS: this kit is V2 ventus version!
With all wing reinforcements in carbon. I also got the PNF version, believe me , just forget it and buy this kit and build it with good material.(I had to rebuild my PNF 80pcnt)
One trick: remove the gear and use the place for the battery then your COG will be perfect.(4,5cm from the front of the wing).
Flying weight is 1120g.
This is a fast glider, not for RC beginners.But it can land slowly thanks to flaps.

• Overall
• Quality
• Value

Customer Rated

Dec 30, 2012

This glider is a great kit that goes together well but it helps to have done some building as some bits are a bit tricky. The hinged ailerons and flaps are quite stiff and I found that I had to add a backing plate and screws to the control horns to stop them being pulled out of their slots after epoxying them on. Also don't forget to install the aluminium sleeve with the two grub screws before you join the halves of the fuselage together which holds the wings together duing flight. Long extension wires are required also as the servos are a long way out on the wings. I am using a 28/26 1000Kv motor 315watt http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=29824
but it is quite tricky to install as there is not easy access to the fire wall etc. I also found I had to reverse the shaft which was a pain as I had to dremell a little groove in the opposite end for the little clip to hold the shaft in. The plane balances perfectly with a 2200 3S nano tech battery so not sure why they had to add tail weight in the HK video. Overall a great plane and the carbon fibre in the wing is excellent. The wing spar is sloppy so I might replace that with a better fitting one. Also added magnets for the canopy hatch.

• Overall
• Quality
• Value

Customer Rated

Dec 28, 2012

I have bought this floater because a special offer was done because I showed interest. The discount was disappeared during checkout.
I am now very disappointed

• Overall
• Quality
• Value

Certified Buyer Rated

Dec 21, 2012

ao contrario do que dizem este aviao muito bom, tem bons acabamentos, tem um EPO muito denso, tem muito apoios nas asas, em relativamente leve, tem um voo muito suave a rapido.





Contrary to what they say this plane is very good, has good finishes, EPO has a very dense, has much support in the wings, in relatively light, has a very smooth and fast flight.

• Overall
• Quality
• Value

Customer Rated

Oct 09, 2012

Kit is really good and the finishing is very smooth.
Wings are reinforced with a carbon spar and carbon strips for the trailing edge are included.
The propeller in the kit is a 10x6 and the spinner diameter 44mm.
This is the V2 ventus, not the first one with flexible wings. Now they are massively strong.
If you want to get a good discount you'll find a buddy code valid until the 21st of October on r c s e a r c h . i n f o
Just write ventus on the search.

• Overall
• Quality
• Value

Certified Buyer Rated

Oct 05, 2012

Brought from the Aus warehouse along with another model, arrived in 4 days! Excellent quality model, the surface finish is extremely smooth, this is the V2 and has the upgraded wing spars, very strong! The boom to tail join is a bit iffy and will be using thin carbon rod to add strength. Will be using a 70mm EDF instead of a motor/folding prop setup, more for fun than soaring!