HobbyKing® ™ Edge 540 V3 (rojo / plata) 1200mm 3D (ARF)

• Overall
• Quality
• Value

Customer Rated

Jan 12, 2014

First balsa model, very lightweight, very nice to see.
The box was OK, hard cardboard, inside no kind of damage.
Assembly was fast, i used much threadlocker to the screws, and epoxy instead of CA. I suggest to reinforce the plywood junctions with more glue! The rudder is push-pull system, i installed a turnigy sk3 3548, not so good for 3d, but its not my flying style yet! So its good to me. ESC 60amp and nanotech 3s 3300mah battery and the tgy 113mg servos.
The covering is ok, i improved it in some minor points with the iron.
The landing gear is made by metal and its very elastic, someone changed it with carbon fiber one, more rigid, but its ok to me because it helps you in not so good landings!
Although the landing wheel are so small the model takes off and lands on the grass with no problem!
The specified cg is ok, someone put it 10mm shorter than the original. To check the cg you have to know that the models fulcrum is right in the middle of the simmetrical airfoil, so you have to keep it hanged by fingers from inside of the fuselage.
I never flown an acrobatic 3d model. There is no dihedral and it has simmetrical airfoils, so no tendency to self-levelling; you have to really fly it! Its not a mess to learn this knife flyer and once you did it is so funny!
The setup must be perfect, you can fly tail heavy but its really hard,

• Overall
• Quality
• Value

Customer Rated

Jul 05, 2013

I thought i'd be the first one to post here and have to say that this is one awesome Edge!



I'm running mine on a 4s 2650 Nano-Tech lipo, 900KV 815W NTM Motor with reversed shaft, 12x6 APC Style prop, 60a Plush ESC, TGY 9018MG servos, and FrSky radio gear. Total weight is 1400g.



I'm really iimpressed with the setup although as per our american friends, the elevator required a small piece of 3-4mm flat carbon to strengthen it up. It seems like they have updated the elevator as mine came in 3 pieces with a strong metal U clamp but i wasn't going to risk it and leave to to chance to break.



Everything was a breeze to install and feels solid and well built. However, my elevator servo mount seemed to be lose/borken (lol) so i had to glue it back together - Not a mahoosive issue but could of caused problems if not spotted!



Amp test results on the 4S 2650 and 12x6 pulled around 53 amps and a few short of 800watts. The plane has plenty of power so no need to push it any further.



It's smooth yet agile, fast and predictable! So a big happy face from me! :D

• Overall
• Quality
• Value

Customer Rated

Jun 01, 2013

Martin Mnster (6) ,einer der jngsten Kunstflug-Piloten in Deutschland, fliegt diese V3. Schn leicht und gute Verarbeitung. Es wurde an einige, entscheidende, Details gedacht ( Fahrwerk, Kabinenhaube, Motordrom) ,die man selbst bei Sebart vermisst.
Allerdings ist ratsam gleich das Hhenruder mittig zu verstrken, oder nach unten und oben abzufangen. Alles in Allem klasse.
http://bm-cs.de/martin oder unter Facebook Siegfried F.Mnster

• Overall
• Quality
• Value

Customer Rated

Apr 17, 2013

Excellent plane, the elevator problem others have listed has been fixed, with the plane being shipped with a metal coupler to join each side of the elevator with.

I am running the NTM Prop Drive 35-42 Series 1000KV, with a 12x8E prop, on 3S 2200mah and i'm getting just shy of 400W WOT @ 40A. This gives me vertical/hover and a reasonable top speed. With this combo i had to add some balsa to the back of the battery compartment as the battery sits quite far back.

I am flying with a CG of 89mm from leading edge, which seems to handle nicely. I haven't tried much 3D manouvres yet as i am still learning 3D, so can't really comment on that, but i suspect i will need to move the CG to the recommended 99mm for that.

Overall and excellent product, and worth noting that my mate was suprised when i told him it was a HobbyKing plane as he thought it was a more expensive brand!!!!

• Overall
• Quality
• Value

Customer Rated

Aug 07, 2012

Following the strengthening of the structure of the horizontal stabilizer made the first flight. Everything was perfect, it was not necessary to set the trim flight. Use battery 3s 2200 to 3000mha without changing anything the CG. Very stable in flight and landing.

• Overall
• Quality
• Value

Customer Rated

Aug 01, 2012

http://www.hobbyking.com/hobbyking/store/HK_movies.asp?idmovie=0aa8b6f8c44f48dfbe508ff189a8e97b

Flying my edge !

• Overall
• Quality
• Value

Customer Rated

Jul 28, 2012

Beautifull plane, light, well built
It is difficult to harrier upright as it tends to rock when you use the rudder to steer, Inverted is more stable
KE has litlle coupling, mainly to the belly and "unrolling" 10pcnt mix take it out
Really flat inverted spins, tracks well, snaps are not fast upright, faster inverted
With a 13x4 and recomended motor it uses 41amps with good but not ballistic pullout from torque roll, Dont use Nanos 2560 25c , they will not last! use bigger capacity or bigger "C" discharge rates, next time I will use Zippys 2800 for a 10gms penalty

• Overall
• Quality
• Value

Customer Rated

Jul 12, 2012

Nice plane for the price. I use a Turnigy Aerodrive SK3 - 3542-1000kv with a 12x6 prop on 4S and it flies really fast. Not as precise as famous quality brands planes (you have to adjust knife edges with quite a lot of elevator for exemple) but for the price it is good and really fun. Be sure to reinforce the elevator with carbon.

• Overall
• Quality
• Value

Customer Rated

Jul 11, 2012

Well packed. Some news about elevator problems, so my plane got carbon fibre sticks from the elevator side to other side. I'm not professional, but this plane quality is nice and also flying nice. Here is one video: http://www.youtube.com/watch?v=pgkqcALnipg&feature=plcp

• Overall
• Quality
• Value

Customer Rated

Jun 14, 2012

It's very nice looking plane. Due to briliant red color, visibility in the air is really good.
And it has sublime flying character, easy to handle & landing.
But horizontal stabilizer is very fragile, reinforcement is crucial.
Except one that defect, it is very recomendable one.