HXT 2445 (370L) 2900kv sin escobillas Inrunner

• Overall
• Quality
• Value

Certified Buyer Rated

Jul 02, 2011

very well built and makes my boat go fast

• Overall
• Quality
• Value

Customer Rated

Jun 22, 2011

Powers my STRYKER with 3s 2200 LiPO and a 5.5x4.5 very quick.and good vertical also the only thing is that the shaft size is just to small dont change any thing but the shaft size

• Overall
• Quality
• Value

Customer Rated

Apr 22, 2011

Nice motor, pushed my X41 deltastorm like a rocket but with a 6x4 prop and 20c lipo got so hot, i burned my fingers. Couple of flight later the motor gave in (after 5 min full trottle) and seized, burning my 40A plush as well. still i find it a good motor. i found the shaft 2mm not to weak but might not survive multiple crashes.

• Overall
• Quality
• Value

Customer Rated

Apr 04, 2011

If you are using this for a propellor driven plane seriously consider getting a motor with a 3mm output shaft. Didn't get one flight in my Stryker as output shaft broke immediately with 5.5x4.5 prop. No replacement shaft is available, too expensive to return so it's in the bin... Please Turnigy put a 3mm sharft in these as there is a lot of potential here.

Very dissappointing...

• Overall
• Quality
• Value

Certified Buyer Rated

Feb 20, 2011

Nice, but little heavy brushless motor.



Shaft is the weakest point. It is narrow from 3 to 2mm and the end of front ball bearing. Other than that it is great value!



With 2S 1800mAh lipo cells and Aeronaut 6x6 floding prop, it consums 35A at full throttle. With this setup it needs good ventilation, because it gets hot quite fast.



The weight with 3,5mm bullet connectors, is 93g!

• Overall
• Quality
• Value

Customer Rated

Jan 22, 2011

Der Motor ist OK, einziges Manko ist der 2mm Schaft, der ist mir schon durch einen unbalacierten Prop abgebrochen, kennt jemand eine Moeglichkeit, den Schaft zu reparieren ?

Good Engine, the only bad thing is the shaft. 2mm is too less, it breaks with a unbalanced Prop, does somebody have an idea to repair the shaft ?

• Overall
• Quality
• Value

Customer Rated

Dec 13, 2010

This Motor has good performance, but the 2mm shaft is very thin for this size and it is very fast getting broken.
Around this reason i'm not going to buy this motor again and I dont suggest it at anyone.

• Overall
• Quality
• Value

Customer Rated

Nov 25, 2010

It installed right perfect on my Losi Mini-Lst 2, not any modifications needed.

The original pinion went straight on the 2mm shaft, and this little beast went straight to original motor mount.

I also installed Turnigy's smaller 35A car esc.

By removing the original motors i had plenty of space for lipo.

on 2s lipo the losi moves very nicely, but on 3s its suprerquick.

The run times are about 15min on my 1800mAh 3s lipo.

This motor doesent get hot at all moving my small car.

If u want more kv:s (and speed ) theres the 3790kv one the same size.

• Overall
• Quality
• Value

Certified Buyer Rated

Nov 14, 2010

Pouziti na rekreacniho pylonacka s vrtuli Graupner 4,7/4,7". Hridel 2mm je na draka, roztece 4 sroubu M3 na prum. 16mm.

• Overall
• Quality
• Value

Customer Rated

Aug 21, 2010

Bought 2 of them. Burned out very quickly, even pulling below amp rating. Disappointed.