Este modelo está caliente!
Una máquina de girar la cabeza EPO 1.4m 3D; este modelo a gran escala seguramente atraer a una multitud en cualquier club y exigir el pleno respeto entre los pilotos en 3D de todo el mundo.
El esquema distintivo y la escala es ideal para la orientación. El MX2 es grande para un modelo de EPO y se ve casi dos veces el tamaño una vez que está en el aire. Es una maravilla de volar y es muy capaz 3D!
El potente, preinstalado hilatura 36-48 motor que gran escala y 3 prop hoja da un montón de empuje para el más salvaje de maneouvers, y los de servo preinstalados son sin duda hasta el trabajo. superficies de control de tamaño generoso combinado con un peso ligero aseguran que esto es un verdadero artista, así como un tornero cabeza. Práctico, así como agradable a la vista, las alas son desmontables para facilitar su transporte, un pabellón grande, se puede acceder a la bandeja de Lipo, tornillos de mariposa y así sucesivamente.
Peso del vuelo: 1900g
Ala Carga: 50 g / dm2
Motor: 42-48 sin escobillas Outrunner
ESC: 70A w / BEC
Servo: 9g x 2, 2 x 17g
Manual de instrucciones
Su Propia 4 ~ 6 Canal TX / RX
Batería 2200mAh Lipo 4S
SKU (Número de Referencia):
Peso ( g)
- SKU (Número de Referencia):
This is a very well made model and flies like a dreamIch habe versucht dieses Modell zu einem vernftig fliegenden Flugzeug zu machen: leider ohne Erfolg, das Merial taugt einfach nicht. Es ist extrem empfindlich, bei etwas hrteren Landungen bricht es sehr leich komlpett durch. Die Flgelbefestigungen sind absolut untauglich, etc, etc. Nach viel Stunden und Reperaturen (und zugekauften Ersatzteilen) habe ich mich genug gergert und werde das Modell "entsorgen", auch wenn es am Boden immer noch sehr gut aussieht.
Sorry HK, ich bin sonst von vielen eurer Produkte sehr angetan!I got this as a gift for my son he is 42. So this is not for son who is a good modler. The instructions are useless and pictures are even worse. The small parts bag was missing many items. The paint on one single panel was bobbles no paint. Flying is good but the CG is very important. No Where in instructions is it providedNice looking model, pity the quality is crap, tail wheel a pain ,control rods to long, elevator rod to long by 15mm , wrongly labelled items. poor manual, screw hols filled with glue, wheel hubs have to be drilled out to allow wheel to spin , tight on bolt so when wheel turns it follows thread and locks up. rudder needs extra hinge, hope it fly's awesome after all the mods and work to get it built.Im going to be as real as possible on this plane. Stock setup will not 3D , the plane is too heavy for this. Flew mines today with a 2650 4s and when she got airborn as soon as i pitched the plane she wanted to snap on me (Wing tip stall) then i landed the plane and tried a lighter battery this time using a 2200 4s , Did much better but still had the snap problem when pitching the plane. Don't Believe what you see in the video in the description of this plane because it will not perform that way with some modifications.
1ST thing i would do is replace the wing spare with a lighter one because thats one problem for the wings. Weight is every important in a aerobatic plane. 2nd Replace the landing gear with carbon fiber lighter ones , these add extra weigt to the plane. 3rd Change out the tires and buy lighter ones. Those 3 items i mention should be replaced to make this plane lighter and fly better.
The stock motor and prop are good enough for this plane to do 3d with , did some testing before i took it out to the field. Other than that it flys pretty good , takes off fast. Just with they would make some changes to the plane and make it lighter.The tail piece on this one may arrive warped. The landing gear holes in the bottom of the fuse don't line up and have to be re-drilled before the landing gear can be re-attached. The landing gear wheels will bind-up and you may need to remove the wheels and remove some foam to allow the wheels to spin freely. The tail wheel arm will likely hit the tail/rudder and may need to be bent to fit. Mine snapped, even with heating first. I had to fabricate a new piece in the correct shape. It's easiest to do this with 2mm aluminium. The motor mount screws are over-tightened and not holding well in the wooden brace. You may need to swap them out for larger screws. The motor has no loctite on the bolts. You should unbolt it all and loctite it all in properly. The servos that come with it are not as advertised. They are full size units (41x20x37) of unknown make/model. They have lots of play and will need to be replaced before you fly, with better quality units, as the rudder/elevator will be too floppy.
Not a good product, but with some loving you can get it into reasonable shape.Great Plane Poor Prop Adapter. Build own one from DURALUMINIUMThe good bits.... Looks fantastic in the air!!, large size and hobbyking are selling the high powered '3D' version with 4258 motor and standard size servos for the elevator and rudder. It is also a very simple assembly.
The bad bits.... mine crashed on the maiden flight after 10 seconds when the stock ESC burnt out. It had not even been past around 60pcnt throttle (it takes off very easy). Was not nice watching a plane that I had bought for its appearance snap in half. An aileron servo also died in the crash, on a wing that was not impacted.
The flying.... I bought this as a nice looking sport flyer, and after spending a weekend repairing it and replacing the ESC, spinner and propeller I got it in the air i confirmed it is an OK sport flyer. Only handling flaws are snapping out of tight loops due to not having enough hinge points in the ailerons, and a relatively high stall speed. It also needs quite a bit more power, probably a 5s upgrade would do it, the motor looks like it could easily take it as it was still cool after flying with 4s. Note I an currently flying with a 13 x 4.5 slow fly 2 blade wooden prop. As far as 3D flying goes.... forget it, I have EPP 3D planes that this isn't even in the same galaxy with, but I knew that before I bought it.