Aquí hay otro pequeño gran kit de balsa asequible para el aficionado tradicional de R / C y el constructor que disfruta de la construcción de modelos de forma de kit.
El cisne rojo es un todo construido, 4 canales, potencia eléctrica planeador parque mosca. Cuenta con piezas cortadas con láser precisos afilados que simplemente ranura junto con poco ruido y el ala tiene un aspecto fantástico cuando está cubierta de cubierta transparente para mostrar de la construcción.
El sistema de energía puede ser un outrunner y 2s pequeño y sencillo de la batería, el uso de micro servos para mantenerla agradable y la luz.
El modelo resultante es un pequeño gran parque vuela velero eléctrico que funciona bien, tiene ascensor alerón / timón de control / / motor, pero es lo suficientemente fuerte como para manejar la extraña '¡Uy!' momento de volantes novatos y suficientemente compacto como para ser transportados fácilmente.
Longitud: 810 mm
4 sistema de radio y canal 4 x micro servos
1550kv 15amp Outrunner
2 o 3s 1300mah batería de Lipo
La hélice (8 x 4)
que engloba películas
herramientas básicas de la manía (cuchillo, papel de lija, etc.)
Manual de construcción que aparece en la pestaña "Archivos" de abajo
SKU (Número de Referencia):
Peso ( g)
- SKU (Número de Referencia):
Nice little kit for the money. need a bit of experience to build it. instructions a little bare to say the least!fantastico, ne ho presi 2 a magazzino e uno sempre con me, 1400k lipo 1500-1600 prop 9*4This kit is THE kit for those who love the old school balsa kit..
Wood is good in general and laser-cut parts saves valuable time.
That said, this is not for beginners, the building notes are nonexistent and it is necessary to go on the net to find build logs, fortunately quite numerous.
I just have two disappointments, after assembling and flying with the Red Swan:
First, it is quite heavy. Ready to fly weighed approx 700gr.
For a wingspan of 1224mm he had to fly fast enough to generate the necessary lift.
Then, the weak point is the horizontal stabilizer. It is very close to the ground and the landing must be perfectly horizontal on a very flat surface. The slightest clod of dirt or grass can easily pull the horizontal stabilizer off.
This happened to me twice. The first time the tail has been torn, I rebuilt the entire tail section in plain balsa, much stronger.
Alas, he clung to a clump of grass and the section of the fuselage near the tail (with holes for pushrods) broke ... :(
That said, it's a nice old school kit for a handyman with experience and a good flat ground for landing.
I posted 3 pictures of my Red Swan ( The under files section Cardinal ) just before the maiden flightNIcely cut kit. A lot of fun to build, and they look great when complete. I wish hobbyking would stock more laser cut kits.Fine construction, precise laser-cut parts, but wrong building instructions:
First, the 2 fuselage sides must be prepared with strengthening sticks first, then glued together with bulkhead parts, servo tray and motor mount in one step to avoid distortion!
Second, the order of wing ribs is wrong in the picture as well as in text part 2.02. Correct is 6 pc. B3 in the middle, then on each side one pc. B4, 5 pc. B5, each parted by a pair of B7 glued at both sides of the balsa spars, finished by one pc. B6. The construction should be done on a board using needles to fix the parts, thus obtaining a straight wing.Fine parts, fitting well, but:
Wrong instruction manual!
The two sides of the fuselage must be built symmetrically without yet glueing the bulkhead parts, the motor mount and the servo base. Only when finished, both sides and the mentioned parts must be fitted together in one glueing step.
Otherwise the fuselage will turn out rather distorted!
Second mistake: the denotation of the wing ribs in the picture of the middle wing part and in textpassage 2.02 is wrong. As there are only 2 ribs B4, but 12 pc. B5 and 4 pc. B6, the correct order must be:
6 (or 8? There are 8 pc.!) ribs B3 in the middle, then, spaced by B7, one rib B4, followed by 5 pc. B5 on each side, each spaced by one B7 part, and one B6 rib to strengthen the edges.
The other two B6 should strengthen the edges of the outer wing parts.Soft package, no cover film, no plans.I missed drawing, so I draw him, I upload to files.
Servos will use HXT500.
Motor temporarily 24 grams hexTronik Brushless Outrunner 1300kv.First flight today with a 2822/17 3s and 8*4 prop. Good 3 axes glider slow rolls, loops, inverted flight. Can be used by a beginner (but foamies will be much more crash rsistant...). The manual is really not here to help and 9 gr servos are too big for the ailerons. I have also replace the supplied leading ege of the wing by a carbon fiber tube 3mm. Despite the inexisting and wrong manual, we had good time with my son building this kit and at the end.... Good surprise....great flying capacities!So much potential ruined by horrible plans. I'm about 2/3 done and am looking forward to flying it. Search for my build thread on RC Groups . Com for build information. It's been a fun build so far (other than the lack of instructions). Wood quality is decent but heavy, packing is good, and fit of the laser cut parts is ok.