Escáner RC 150A ESC (1 / 10Scale)

• Overall
• Quality
• Value

Certified Buyer Rated

Mar 12, 2012

dont use this for a 2.5t cant take the punishment

• Overall
• Quality
• Value

Customer Rated

Jan 05, 2012

I just wanna say good job, this ESC is totally powerful, I am still using and working well!! especially the new version 2 is also adding top fan case for better protect.

• Overall
• Quality
• Value

Customer Rated

Nov 29, 2011

no more word, the ESC is top quality and 150A MOS-FET is enought for most Brushless motor, I am very happy with nice price too, thank HobbyKing, good job!!~!

• Overall
• Quality
• Value

Customer Rated

Nov 02, 2011

ESC ben fatto ,e senza nessun problema di assemblaggio,molto semplice da settare (ho tradotto il manuale da inglese in italiano)con la radiotrasmittente.

Lo provato su una barca per dieci minuti e riscalda molto poco.

L'inconveniente e che ESC non e settabile col Turnigy 2 in 1 Professional Program Box for Brushless ESC ,e col

TURNIGY BESC Programming Card,

foto del manuale tradotto in ITALIANO su FILES

• Overall
• Quality
• Value

Customer Rated

Oct 22, 2011

Bad, bad, and bad...

Bought 2 and both burned, one in 3 gas pulls, the other one was 5 batteries, both with 6t ScannerRc motor.

I dont recomend this speed controler.

• Overall
• Quality
• Value

Certified Buyer Rated

Oct 20, 2011

ok lo provo e scrivo i commenti

• Overall
• Quality
• Value

Customer Rated

Oct 04, 2011

I bench tested this esc with a 2800kv motor with 3s battery. it wasn't right from word go and within 10 min it developed a dead short. It never even made it into a car.It's been over 1 month and HK are still in the process of checking it, therefore i would not advise buying one

• Overall
• Quality
• Value

Customer Rated

Sep 22, 2011

I receved mine yesterday, in despite of a lot of negative coments i decided to buy it.
The ESC is not like that photo, is more like this:
http://imageshack.us/photo/my-images/560/20092011002.jpg/
http://imageshack.us/photo/my-images/853/20092011003.jpg/
It comes with 14AWG wires, so it is not difficult to doubt if it can really handle 150amps.
I am using it in my pan car 1/10 and scanner 6000kv brushless, it does not warm, probably works on 40C with this combination (17-81 teeth and small diameter tyres)
the fan is powerful, it makes "windy" arround the car. The BEC DOES NOT work at 5 volts, it works at 6 volts, measured by my voltimeter.

BE CAREFUL be sure that the phases are U with A, V with B, and W with C in sensored mode.

IT WORKS SENSORLESS TOO

the instruction manual is very poor, and to program it you'll need the programing card, or actually I didn't find the way to get in the programation with the programming button.

the screws CAN'T touch the fets, someone wrote that, at least in mine it is impossible, it has only 4 to hold the fan holder and the underbox.

I can't tell you more by the moment because it has some minutes of use, by the moment it seems a cheap ESC not too much powerful, and smooth, for 1/10 4x4 touring car it will need 12AWG wires. that is all hope I can help you.

• Overall
• Quality
• Value

Customer Rated

Sep 18, 2011

Really not happy with this esc, only ran it a few times, put a 3s thru it and it died. Took the esc out and i shook it because i heard a rattle, one of the drive chips had come off and was rattling around inside the case. Id go for a HK equivalent for the extra couple of quid.

• Overall
• Quality
• Value

Customer Rated

Aug 20, 2011

Very good ESC!
But works only in sensored mode. I try to run whith sensorless mode and its always "beeps" and not work