La forma más fácil de poner retrae en su avión. No es necesario instalar una caja de control, cableado desordenado o un sistema de aire complicado. Simplemente atornillar se retrae, conectarse a su Rx y ya está listo!
servo mecanismo confiable con engranajes de metal y un motor de alto par asegura problemas para el vuelo libre!
¿Por qué molestarse con los sistemas de aire cuando ahora puede tener una unidad eléctrica realista y fiable a una fracción del precio ?!
3 segundos sobre la protección actual y se obstruye
Incluir apropiado para torcer el grado puntal 90 cuando se retrae
circuito inteligente mantiene la unidad retraído aunque conecte la alimentación. Sólo la señal del transmisor puede extender o replegar el tren.
Voltaje de funcionamiento: 4.8 ~ 6.0V
Corriente de trabajo: 0.1 ~ 0.3A (3 segundos sobre la protección actual)
No es adecuado para un avión más pesado que el de 2,5 kg
SKU (Número de Referencia):
Peso ( g)
- SKU (Número de Referencia):
The Servoless Retracts are an excellent product. Very good value for money and they perform well. Im a big fan of the MainRetracts (STTE-2) which HobbyKing also sells (or used to). The NoseWheelRetracts (STTE-3) can be setup in several ways. Click the FILES tab above and find 'RetractInfo -LaserBeam' for the INSTRUCTION MANUAL for the STTE-2 and the STTE-3 servoless retracts. ie. Instructions for BOTH the Main Retracts and the Nose-wheel Retracts. Its in .PDF for best viewing. Enjoy :)Ebenfalls vorgesehen fr Parkzone T28Gute mechanik, alles Bestens.I connected to my Futaba 8FG and R6208SB. Works great. No EPA adjustment necessary. I was hesitant to buy this because of other reviews but, as long as you dont repeatedly test cycle them, they should last a long time. Mounting depth is 23mm!I orderd three of these and 3 packets arrived with my order but 1 packet was empty. A service ticket was opened then promptly closed as being "resolved" but numerous contacts made and still no replacement or credit for the missing retract. So I'm giving a now incomplete and hence useless set of retracts 1 crown. Com'on HK some follow up and service please.It has a huge gap in any position. Otherwise, it is cheap and works where precision is not required. I'll try to minimize the gaps. Never mind the warning not to open because it is quite easy reassembling.
Solid retract, using on 70mm EDF jet.The leg fit into the unit is very sloppy causing imprecise steering and imperfect retracting, also either steering system (pull-pull or pushrod) is not easy to setup.
If using the pull-pull system for steering the leg's looseness causes it to rotate when retracting frequently causing a jam, if using the pushrod system for steering it jams up often too as the parts don't always line up.
The price matches the quality, mine is however, still operating fine after 100's of (testing) cycles.This is a Changesun electric retract. Quality is correct for the price tag. Works flawlessly with a 2,4ghz Futaba receiver. Mounting this on a 2,5kg model seems a bit optimistic too me. I wouldn't install this on anything heavier than 2kg.I tried these for the F9F Lander Phantom, which had to be extensively modded to make them fit.
The shaft is 1/8", not 3mm. No mounting screws are provided.
The leg is made from carbon steel. You will not be able to bend them without heating them. I think they are made to interface with other wheel assemblies normally.
I used a butane torch to heat the areas to bend and was able to made a nice front leg arranegment from it but you need to heat the leg to glowing red hot.
Naturally, you should remove the leg from the assembly first. It is retained by a circlip. Finally, I think the jam detction is overly sensitive. It stops at the slightest resistance and am not sure it will have enough torque to pull the steering cables tight before the anti-jam kicks in.