1700kv Turnigy 2211 de motor sin escobillas

• Overall
• Quality
• Value

Certified Buyer Rated

Jul 02, 2013

meiner war leider defekt! :-(

• Overall
• Quality
• Value

Certified Buyer Rated

Feb 17, 2013

Perfect replacement for the Mini J3 Cub motor also here on HobbyKing.

• Overall
• Quality
• Value

Certified Buyer Rated

Dec 22, 2012

Luft schn ruhig und zieht wie ein Groer. Pull-Angaben sind korrekt.

• Overall
• Quality
• Value

Customer Rated

Aug 01, 2012

Motor does not work. I burned out ESC. With another ESC motor just try to turn. After few seconds motor smoking. I tried change timing and also smooth start but without success. Completely wrong! They do not have output quality process in a factory?

• Overall
• Quality
• Value

Certified Buyer Rated

May 16, 2012

Cracking little motor

• Overall
• Quality
• Value

Customer Rated

Apr 30, 2012

I like this motor (and its smaller cousin the T1811-2000). Have been doing some static bench tests and here's some info so far. Hope it's useful to others:

prop:Amps:Volts:Watts:Thrust(grams)
7x3.5:2.7:7.76:20.9:133
7x6:3.5:7.57:25.7:119
7x6:4.x:7.x:?:140 <- (put it here real quick to see thrust, but didn't keep it long enough to see other numbers as I didn't want to risk over current. After a few seconds at this amperage the motor was very very slightly warm to the touch)

Of the limited set of props I tested I'm going with the 7x3.5 as it keeps the amps down and, hence, flight times should be longer. I'm targeting a 3D foamie for this that has a AUW of around 93 - 105 grams.

Thanks.

• Overall
• Quality
• Value

Certified Buyer Rated

Apr 18, 2012

Neat, and small electric motor.

Power is good.

• Overall
• Quality
• Value

Customer Rated

Apr 12, 2012

I bought two of these for the tail of my cp heli. After installing the first one, i found that the set screws at the base did not properly fit in the holes. The second one was fine, so i guess i have one for spare parts. Works good, i'm gunna try the 2300kv next. Yes, i will buy two (just in case).

• Overall
• Quality
• Value

Customer Rated

Dec 26, 2011

I got a love/hate with these motors. I've bought 4 so far and use them exclusively in the Bonsai wing where they work great on a 2s 860ma Zippy with a 6amp Plush speedy. Flight times are well over 20 mins and gentle flying gets me to about 40 mins . With this setup, everything is almost cold to touch at end of flight. Won't quite hover though, but I reckon 3s would do it easy.



Here's the bad. The wires coming out of the motor are simply the ends of the windings which are twisted together. There is no support for the wires and since the windings are solid core (1 strand only), they cannot handle much flexing before they break. They're a real @ to solder back in place as they tend to break off at the base leaving almost no wire to work with. As I'm using these on Bonsai wings, there's not much protection and after a while, they will all fail unless you take some "Anti-Wire Flexing" actions to keep them safe.



Working with the Plush 6A ESC, they tend to work great when they're brand new, but after a week or so, they start cogging at start up. This seems to be motor related because if I connect another motor - no cogging. Mind you, sometimes they cog from brand new too. I suspect it's to do with resistance build up from flexing. I'm going to persist with these motors as I really like them when working well and will make more mods to make them reliable. Todays mod will b

• Overall
• Quality
• Value

Certified Buyer Rated

Jul 10, 2011

bem pequeno e rpido. parece ser bom