Turnigy MultiStar 30A BLHeli-32 4-in-1 Race Spec ESC w/ F4 FC, OSD & BEC (2-4S)

The popular Multistar 4-in-1 ESC 30A BLHeli_32 just got even better with the addition of a powerful F4 flight controller and a Betaflight OSD. The weight saving of this 36mm x 36mm combined all in one unit is fantastic as it only weighs 16.5g (without wires).

The F4 processor is gaining popularity in flight controllers due to the advantages in additional processing power and it is packed with features. The processing speed of the F4 processor is more than double that of the F1 and F3 (from 72MMz to 180MHz) which gives it incredible precision and control whilst flying.

The whole unit is very light and compact and has an easy setup process. it is the perfect solution where you are looking for outstanding performance in one small and neat package. Turnigy MultiStar BLheli_32 32bit ESCs feature a proprietary firmware that delivers a smooth linear throttle response, without sacrificing a rapid, crisp response to your throttle inputs. Each 4-in-1 ESC has plated connections to allow you to easily solder your motor wires directly to the PCB and then add your preferred connector to the pre-tinned power cables

Features:
• Compact all in one unit (4 x ESCs, FC, OSD)
• Lightweight (16.5g)
• Am Cortex-M10 MCU
• Fast response to throttle input
• Smooth and linear throttle control
• Throttle signal loss protection
• Stalled motor protection
• Supports 480Hz refresh rates
• Supports Dshot150-300-600/Multishot/Oneshot protocols etc
• Betaflight OSD

Specs:
Continuous Amps: 30A (each ESC)
Voltage Input: 2-4S (4.2-16.8V)
BEC: 5V-2A:5V-3A
Timing: Auto
Dimensions: 36 x 36mm
Mounting Holes: 30.5 x 30.5mm
Weight: 16.5g (no wires)

Subir video

Regístrese para subir videos, por favor Iniciar Sesión o registrarse

Temas

Ordenar por

Temas más recientes

Publica un tema nuevo

Regístrese para escribir reseñas, por favor Iniciar Sesión o registrarse

Paranut | Comprador verificado

Overall
Quality
Value

Useful tips....

Feb 26, 2022

The Sbus line works inverse. So it will not accept Ibus etc, only Sbus. There was a guide somewhere to use another line (LED) for Ibus input. Use google. Also, it took a while to work out the flashing of new firmware. It seems flashing and general comms are different drivers. Again, lots of googling solved it. I didn't save the links, but maybe the above will help you.

VOiD | Comprador verificado

Overall
Quality
Value

Great!

Apr 09, 2021

Great!

Sigi | Comprador verificado

Overall
Quality
Value

Faulty device received

Mar 24, 2021

Unfortunately I have received a faulty device.
HK wants me to return it via tracked method which costs € 26.90 due to Brexit.
RMA claim still in process.

Dion | Comprador verificado

Overall
Quality
Value

Very good All-in One.

Jul 05, 2020

Very good all in one board.
Things that are needed for betaflight/cleanflight,
You need to download the usb drivers via betaflight on its page.(on the program page)type of driver (winUSB driver),other drivers will corrupt chip so becarful.,cos the chip will brick its self in ether com3 or DFU.So make sure you put the right driver in.The software for this chip is utter crap.Use betaflight ect..Dont go searching for pre-installed software cos its not downloadable...
Target for betaflight is:OMNIBUSF4.,Any othe firmware will brick the chip,so be careful.
Now if you want to reconfigure your chip so the usb input on the chip can be put on the side?,set it up under betaflight,On the Settings screen.
Remember too download the latests betaflight/cleanflight first! Before any of this.
Good luck and hope this helps you out,as i had too learn how to config this myself!! cos no one had a clue.,Chip 10/10

Dion | Comprador verificado

Overall
Quality
Value

Very good All-in One.

Jul 05, 2020

Very good all in one board.
Things that are needed for betaflight/cleanflight,
You need to download the usb drivers via betaflight on its page.(on the program page)type of driver (winUSB driver),other drivers will corrupt chip so becarful.,cos the chip will brick its self in ether com3 or DFU.So make sure you put the right driver in.The software for this chip is utter crap.Use betaflight ect..Dont go searching for pre-installed software cos its not downloadable...
Target for betaflight is:OMNIBUSF4.,Any othe firmware will brick the chip,so be careful.
Now if you want to reconfigure your chip so the usb input on the chip can be put on the side?,set it up under betaflight,On the Settings screen.
Remember too download the latests betaflight/cleanflight first! Before any of this.
Good luck and hope this helps you out,as i had too learn how to config this myself!! cos no one had a clue.,Chip 10/10

Birdy | Comprador verificado

Overall
Quality
Value

Not bad.

May 10, 2020

Over all a good product, A Bit pricey.

lars | Comprador verificado

Overall
Quality
Value

great!

Mar 17, 2020

works great no problems here

MR LEE | Comprador verificado

Overall
Quality
Value

The multistar can be fearful

Mar 13, 2020

Fantastic board all round oh well the tx6 rx6 are very small pads happy flying 8 out 10 and hobby king customer service is very helpful qwick refunds

Mr. B | Comprador verificado

Overall
Quality
Value

Can't be beat!

May 27, 2019

I absolutely love these. This plus a VTX and your off to the skies, simple as that! Only complaint is that there's only one UART. Still, for the money, it's hard to beat.

Mr. B | Comprador verificado

Overall
Quality
Value

Hard to beat!

May 08, 2019

Considering it's an all-in-one package (sans receiver and vtx), it's hard to beat for the cost and convenience!

Archivos de clientes

v6-7-5-driver-serial-enum-release-notes.txt	Download [14]
v6-7-5-driver-serial-enum-release-notes.txt	Download [14]
v6-7-5-driver-serial-enum-release-notes.txt	Download [14]
v6-7-5-driver-serial-enum-release-notes.txt	Download [14]
wiring guide	Download [383]
glowrider.jpg	Download [2]
ZMR Slim Build.jpg	Download [5]

Subir archivo

Regístrese para subir archivos.
Por favor registrarse o registrarse para empezar a ayudar a los aficionados ahora!

Configuración

Choose language

Configuración

Choose Currency

Configuración

Choose Country