-
Description
du -
Vous cherchez à faire votre plate-forme vidéo ultra-lisse? Ceci est l'ultime en pole haute usage de comptage intégré brushless moteurs cardans lisses.
Le moteur 2804 est livré avec un montage encastré de sorte que tout bricolage à des projets PRO sont simple et direct, il est également livré avec le connecteur femelle standard pré-installé, donc le câblage est aussi simple que brancher. Il est un match parfait pour notre Brushless Gimbal stabilisation Conseil et IMU.
Le 2804 est la taille parfaite pour les caméras autour de 100-300 grammes (style GoPro).
Spec:
Polonais: 12N14P
KV (RPM / V): 210
Résistance: 10.4omh
Poids: 35g
Wire: 0.19mm
Couple: 240g
Bottom centre de trous du centre: 16mm et 19mm
Top centre de trous du centre: 12mm -
Product
Specifications -
Informations supplémentaires
-
Référence:
047000029-0
-
Brand:
Non
-
Poids (g)
31.00
-
Longueur
35.00
-
Largeur:
15.00
-
Taille:
35.00
-
Kv ( rpm / v)
210.00
-
Max Currents (A)
0.00
-
(W ):
0.00
-
Longueur B ( mm ):
15.00
-
Longueur Can D ( mm )
10.00
-
Max Tension (V)
0.00
-
Arbre A ( mm ):
0.00
-
Unit Weight (g):
35
-
Diamètre C ( mm )
34.00
-
Longueur totale E ( mm )
15.00
-
Résistance ( mh ):
10.00
-
Référence:
-
Community
Discussions -
-
Rate&
Review -
Good motor, I use it for roll in a 3 axis gimbal, I enlarged the threads to 3mm though. very simple to do, just disassemble the rotor and insert a 3 mm tap, work slowly, add a bit of oil. No predrilling required. Assemble it back. Bought two, one had a minute play if you pulled on the rotor casing, just put it on a board of soft wood rotor down and slightly tap it with a small hammer on the shaft (circlip end, do not remove the circlip) checking for play. Adjust the hammer power by slightly increasing it if there's still play. Don't over do it!I used these for a decently heavy 3D printed gimbal of my own design. The camera housing weighed 325 grams and these motors worked fine, but was nearing the threshold of over-drawing the 500 mA max that the Tarot gimbal control gives. I tried to use these motors on a 425 gram camera and they would not stabilize the gimbal within the 500 mA allowance of the gimbal controller.
If you decide to design your own gimbal, these will work great on cameras in the 100-300 gram threshold. Remember that gimbal design is mostly about balance than it is about torque. Also, the more jostling your quadcopter or craft does, the more torque you have to put out. So, test your stuff on the ground liberally before flying it!these motors should have high quality bearings with no clear ens to the axles images are shaky and a lot of wobble, my next motors will be of a higher qualitymeka kama nahe podi e ne nedaI bought 6 units of this motor and only 2 of them work. The windings are open on the rest. Hobbyking needs to improve quality checks ASAP ! I also bought 3 controller boards and 1 unit came with a DIODE bad. Had to replace it myself.Perfect motor for GoPro H3 (Roll-axis). Buy the smaller motor for pitch.
Smooth and silent. Very happy with mine.enfin ces moteurs chez HK , la on va pouvoir ralis ces propres nacelles a moindre cot comme d'habitude chez HK.
merci -
Upload
Videos -
Upload
Files -
Seuls les utilisateurs identifiés peuvent télécharger les fichiers. Merci de vous connecter ou de vous enregistrer pour commencer à aider les autres membres dès aujourd'hui!
- acc