Devenez fournisseur Blog Nouveaux articles
S'inscrire

Prix total

0,00 €

Panier 0 Panier 0 Loading...

Strip alliage LED bleu 5W 150mm x 12mm (3s Compatible)

Generating Links

Strip alliage LED bleu 5W 150mm x 12mm (3s Compatible)

Prix:

Now save économisez 0,00 € 0,00 €

7,24 €
Déjà acheté Discontinued Product

Please continue searching for a similar product.
SKU:
371000068
Livraison gratuite? Cliquez ici pour apprendre plus!

Strip alliage LED bleu 5W 150mm x 12mm (3s Compatible)

Spécifications:
Dimensions: 150 x 12mm
Poids: 8g
Connecteur: JST
Angle de faisceau: 120 degrés
Puissance: 5W
température de couleur: 460-465nm
Tension: 11.1v-13.5V (3s LiPoly)
: 300mA
Le flux lumineux: 400-450LM
Couleur indice de rendu: 70-85
Matériel: plaque d'aluminium
Durée de vie: 50000 heures
Température de fonctionnement: -20 à 60 degrés Celsius

* Remarque: s'il vous plaît assurez - vous que la consommation de courant est inférieure à 300mA ou vous risquez d' endommager la bande de LED
Télécharger une video

Inscrivez-vous pour télécharger des vidéos, s'il vous plaît se connecter ou s'inscrire

Sujets
Trier par
Sujets les plus récents
* Surnom:

* Votre réponse:


Veuillez saisir le texte affiché dans l'image dans le champ ci-dessous
*Code de vérification:
Annuler
Soumettre
Publier un nouveau sujet
* Surnom:

* Votre sujet:



Veuillez saisir le texte affiché dans l'image dans le champ ci-dessous
*Code de vérification:
Sujet du message

Inscrivez-vous pour écrire des critiques, s'il vous plaît se connecter ou s'inscrire

zaubara | Acheteur vérifié

  • Overall
  • Quality
  • Value

Customer Rated

Nov 29, 2015

I run them with a Meanwell LDD-300L (http://www.meanwell.com/mw_search/ldd-l/LDD-L-SPEC.PDF) switching DC current driver to ensure the leds are driven within rating despite the battery voltage (you can run them from about 10V to 36V input voltage). They are very bright, but only heat up to about 40C. Additionally, this driver has a PWM input (up to 1Khz, not servo-PWM) which I have connected to a GPIO of my Pixhawk flight controller using a N-FET inverter (the GPIO can't drive the current neccessary for the PWM input, I've used 100 Ohm in series to the gate for protection, 100K pull down on the gate and 1K pull up to the battery voltage on the drain). Using the PX4-built-in application gpio_led, the led stripes begin to blink when the battery reaches a low voltage.

| Acheteur vérifié

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Dec 14, 2014

Extreme Bright ! be careful, the polarity its reversed on JST connector, you must solder a 4.7ohms/1W in series to avoid overheating. Do not look directly over short distances

srbell | Acheteur vérifié

  • Overall
  • Quality
  • Value

Customer Rated

Jun 04, 2014

Awesome for brightness! I read some of the reviews and thought I could deal with the heat... Unfortunately it gets so hot on 3s the solder melts and the wires fall off! Too bad, because they look great. Totally unusable.

sportsfanatic | Acheteur vérifié

  • Overall
  • Quality
  • Value

Customer Rated

Jan 13, 2014

This thing is very bright but way too hot. I'm not sure what you could put this on without damaging it. Certainly not foam it would melt it seconds. Only the red color stays cool but it has what I think is a regulator in line.

CopterCrew | Acheteur vérifié

  • Overall
  • Quality
  • Value

Customer Rated

Sep 11, 2013

ridiculously bright which is cool BUT COOL the lights aint, as mentioned in the other reviews they get WAY too hot and will drain a 1000mah 3S in about 2 mins..... Tried it on 2S but it barely lights up, guess will have to try a 9-10v set up but not too sure what to do, any suggestions?

roballoba | Acheteur vérifié

  • Overall
  • Quality
  • Value

Customer Rated

Aug 06, 2013

WAY TOO HOT TO HOLD!!! would probably melt your airplane. These are super bright!! LOOKS AMAZING!!! I would like to mount 6 on my hexcopter, but they will need a WAY bigger heat sink... REALLY HOT!!!!!!! did I mention how awesome they look though?!?!?!?

Noobie | Acheteur vérifié

  • Overall
  • Quality
  • Value

Customer Rated

Aug 03, 2013

I just got this and tested it. It's super bright but it gets very hot really fast so I'm not sure how well this will hold up.

Téléverser un fichier

Inscrivez-vous pour télécharger des fichiers.
S'il vous plaît se connecter ou s'inscrire pour commencer à aider les amateurs maintenant!