S'inscrire

Product Finder

Options

Useful links

Discussion en temps réel
 
[["US","AU","GB","DE"]]
S'inscrire

Strip alliage 5W LED blanche 150mm x 12mm (3s Compatible)

Strip alliage 5W LED blanche 150mm x 12mm (3s Compatible)

Discontinued Product

Please continue searching for a similar product.
Rating:
Stock:
OUT OF STOCK
Poids
10 g
SKU:
371000065
Description
du

Strip alliage 5W LED blanche 150mm x 12mm (3s Compatible)

Spécifications:
Dimensions: 150 x 12mm
Poids: 8g
Connecteur: JST
Angle de faisceau: 120 degrés
Puissance: 5W
température de couleur: 6000-6500 ± 200K
Tension: 11.1v-13.5V (3s LiPoly)
: 300mA
Le flux lumineux: 400-450LM
Couleur indice de rendu: 70-85
Matériel: plaque d'aluminium
Durée de vie: 50000 heures
Température de fonctionnement: -20 à 60 degrés Celsius

* Remarque: s'il vous plaît assurez - vous que la consommation de courant est inférieure à 300mA ou vous risquez d' endommager la bande de LED
Product
Specifications

Informations supplémentaires

  • Référence:
    371000065
  • Brand:
    Non
  • Capacité ( mAh )
    Non
  • Poids (g)
    10.00
  • Longueur:
    155.00
  • Largeur:
    5.00
  • Taille
    45.00
Community
Discussions
Rate&
Review

Écrivez votre propre avis

Only registered users can write reviews. Please, sign in or sign up

verified_user Quality
trending_up Value
playlist_add_check Overall
I have to agree with the other reviewers on this LED strip. It claims it's 3S compatible, but it gets EXTREMELY hot when connected to a fully charged 3S pack. A resistor is necessary to run this with 3S.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I run them with a Meanwell LDD-300L (http://www.meanwell.com/mw_search/ldd-l/LDD-L-SPEC.PDF) switching DC current driver to ensure the leds are driven within rating despite the battery voltage (you can run them from about 10V to 36V input voltage). They are very bright, but only heat up to about 40C. Additionally, this driver has a PWM input (up to 1Khz, not servo-PWM) which I have connected to a GPIO of my Pixhawk flight controller using a N-FET inverter (the GPIO can't drive the current neccessary for the PWM input, I've used 100 Ohm in series to the gate for protection, 100K pull down on the gate and 1K pull up to the battery voltage on the drain). Using the PX4-built-in application gpio_led, the led stripes begin to blink when the battery reaches a low voltage. The PWM input can just left unconnected if not needed.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
They get very hot. Run at 9.0VDC and make sure of polarity. Some of the JST's are improperly assembled
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
This LED has been tested by me on my plane and have to say that in clear weather the LED was visible even at a distance of / - 350 m.
Led is on the leading edge of the wing glued with glue 302 HK.
as power supply is a 3s lipo and use a 10-ohm resistor-10watt.
Will in the future several models of these LEDs provide.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Do NOT connect it to fully charged 3S directly!
Never!
Only 2S
(or LiFePo4 half charged)

Good product!

It should work as a LED - via resistor or LED driver.

Vdrop:
8.40V * 200mA
8.69V * 300mA
8.95V * 400mA
9.07V * 450mA
9.22V * 500mA
Put resistor in series R=(Vbat - Vdrop)/I (choose current you want) Resistor 1-3W (P=(Vbat - Vdrop) * I )

Don't know how long it survive if get wet or in a cold weather.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Tested with 11.1V 3S lipo. Very bright although theres a need to keep the current to 300mA to prevent overheating.
*It is so bright it blinds ur eyes.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
tres lumineux, bien visible l'exterieur en pleine journee, chauffe assez fort, contrairement a ce qui est annonce le courant consomme est de 1,1 A sous 12V, ce qui fait plus de 12W, plein d'applications possibles...
verified_user Quality
trending_up Value
playlist_add_check Overall
Upload
Videos
Upload video
Upload
Files

Seuls les utilisateurs identifiés peuvent télécharger les fichiers. Merci de vous connecter ou de vous enregistrer pour commencer à aider les autres membres dès aujourd'hui!

Customer files
No File Name Télécharger maintenant [1805kb]

Étiquettes des produits

Utiliser des espaces pour séparer les étiquettes. Utilisez des apostrophes pour les phrases.