Afficher : TOUTES CATÉGORIES 0 Modèles volants 1922 Avions 1086 Avions 145

70mm EDF Fighter Jet - Fibreglass 620mm (ARF)

70mm EDF Fighter Jet - Fibreglass 620mm (ARF)

7 La Revue

Prix:

Now save économisez 0,00 € 0,00 €

77,98 €

Déjà acheté Discontinued Product

Please continue searching for a similar product.

SKU:

189000001

Livraison gratuite? Cliquez ici pour apprendre plus!

Partagez ce produit et gagner 400 points (3,90 €) [ ? ]

Description du produit

Le HobbyKing 70mm EDF chasseur regarde certainement la partie et à la suite de la construction de qualité, est un modèle jet à haute vitesse très capable. Ce jet a été conçu pour être un dogfighter et ce modèle arbore un tout empennage déplacement et bons ailerons de taille de pour donner au pilote RC le genre de maneoverability que ce combattant est célèbre pour. Wing / construction d'ascenseur est noyau de mousse / feuille balsa, le fuselage, la consommation, la canopée et stab vertical sont composites, le capot du ventilateur est amovible et une feuille de tube eflux est inclus.

Ceci est une haute performance à jet d'échelle abordable et pratique qui vous donnera de nombreuses heures de plaisir, une unité de ventilateur 70mm est inclus et le coût total de construction devrait être faible pour un tel modèle de qualité agréable. Grands regards, faible coût de construction, construction de qualité, grand dépliant et bien sûr des performances balistiques, que pourriez-vous demander de plus!

Spécifications:
Envergure: 620mm
Longueur: 985mm
Voler Poids: 1200g ~ 1350g
70mm EDF

Comprend:
unité 70mm haute vitesse EDF avec 4mm & 3.17mm adaptateur
Tout le matériel
Eflux Tube
Autocollants
Instructions

A besoin:
Your Own 4 canaux TX / RX
4 x couple élevé MG Micro Servo
Min 28mm EDF moteur Brushless
60A ESC
Batterie 2200mAh ~ 2650mAh 4s Lipoly

Spécifications du produit

Vidéos

Télécharger une video

Inscrivez-vous pour télécharger des vidéos, s'il vous plaît se connecter ou s'inscrire

Discuter 0

Sujets

Trier par

Sujets les plus récents

Publier un nouveau sujet

La Revue

Inscrivez-vous pour écrire des critiques, s'il vous plaît se connecter ou s'inscrire

DeltaDart | Acheteur vérifié

Overall
Quality
Value

Customer Rated

Nov 20, 2013

This airplane is under-powered with a 4s set up. I installed an E-Flite 15 brushless motor with a Turnigy 4s 2650 mah, 14-blade EDF unit. Thrust output was well below anticipated thrust. I suspect the duct opening is too small and not enough air is getting to the motor. Bench check the motor set up and the thrust was incredible. Again, I suspect the duct inlet is too small. Anyone come up with a solution for more thrust?

Russell | Acheteur vérifié

Overall
Quality
Value

Customer Rated

Oct 29, 2012

Well I got mine and the packaging was great. I too dint have instructions however did download the slides from the international file of this same plane. I have had it for a month and have it built. Do want to do retracts but the F-16 ones I have found put the retracts in the intake. It's to thin to do that. I'll figure something out. I. Like the plane and would recommend to someone with time and the skills to adapt the balsa for your needs.

slaanesh | Acheteur vérifié

Overall
Quality
Value

Certified Buyer Rated

Sep 04, 2012

Nice kit. A few issues: 

A bit heavy. 

Needs a fair bit of build experience. 

Wing and elevator covering is good but it's painted and easily chips off. 

My setup: 

Change Sun 10-blade EDF 

Turnigy L2855 2300Kv motor on 5S 

Nanotech 2200mah 45C 3S and 3S in serial 

Turnigy 60A Plush ESC 

HobbyKing 939MG servos for elevators 

HobbyKing HXT-900 servos for ailerons 

COG 77mm from leading edge of wing where it joins fuselage. 

12mm elevator throws 25pcnt Expo 

5mm ailerons throws 25pcnt Expo 

Weight ready to fly 1320g 

Unflown. Maiden when the weather is favourable.

starefly | Acheteur vérifié

Overall
Quality
Value

Customer Rated

Aug 04, 2012

It finally took the air after an unlucky first attempt during which I broke a wing. It has to be bungee launched with my setup to get a good elevator response on start.
Setup:
- EDF FAN 6904
- Motor: HET 2W20
- LiPo 3300mAh turnigy 30-40c
- 100Amps ESC
- CG 70mm at wing root
- Elevator 18mm travel
- Airleron 7mm travel

Behavior in flight is pretty good but need to be trimmed pitch up. Plane is fast and you easily lost him if you go too far away due to its small size....
First landings are a bit hard as the plane is coming fast but after few runs you are able to master beast ! :)
Nice little jet with good flying characteristics for the price, I will recommend !

CHRIS | Acheteur vérifié

Overall
Quality
Value

Customer Rated

Jun 10, 2012

To make a long story short: I do not recommend Hobby King.
You will be better off supporting your local hobby shop where your SERVICE will be better and they will take care of you-unlike HK.
This purchase shall be the last -so savor the flavor HK -I am done.

CHRIS | Acheteur vérifié

Overall
Quality
Value

Customer Rated

May 17, 2012

My order just arrived and the directions did not come with it. I specifically ordered it because the product description said it came with building directions...unlike some kits that do not.

Also, to add to my nice day (sarcasm) the plane came with a not-so-good packed airplane and one crushed right wing tip.

What a bummer...I will keep you all posted here on how HK handles this matter. I will not hesitate to tube this if i get burned.

Kyle | Acheteur vérifié

Overall
Quality
Value

Customer Rated

Sep 14, 2011

Ok first off there are no directions. Alot of the assembly is up to you for example its not clear where the edf unit goes or how it mounts. Same with the servos, there doesnt seem to be spot for them. The canopy doesnt have any way to mount it that I can see. It comes with magnets but where do they go? No landing gear, you get what in the images and nothing more. It will be a fun project for some and something that never gets in the air for some others.

Manuels / Fichiers

Fichiers clients